Search found 120 matches

by robin
Mon Mar 18, 2019 4:43 pm
Forum: Resins
Topic: B9 Emerald Castable Resin Testing
Replies: 22
Views: 13738

Re: B9 Emerald Castable Resin Testing

Are you guys having good success casting the prints from the Solus and what is the best castable resin? PhenQ | https://phenq-reviews.com The new emerald resin seems the easiest to print and also casts well. This is not the public place where not the casting and mandatory involve Huh? http://transl...
by robin
Mon Mar 18, 2019 4:40 pm
Forum: Resins
Topic: B9 Yellow Castable Resin Testing
Replies: 39
Views: 18770

Re: B9 Yellow Castable Resin Testing

[quote="smokepl"]
NYC casters are PITA when it comes to casting. /quote]

HA! I'm in the same boat as you are. I don't want to bad mouth certain casters publicly so PM me and we'll compare notes!
by robin
Sat Mar 16, 2019 1:42 pm
Forum: Casting
Topic: solus wax burnout
Replies: 8
Views: 1858

Re: solus wax burnout

Messerbr wrote:The EasyCast resin seems to print a little better than the emerald and reaches a full cure in UV a little quicker


Are you microwaving it as well as UV curing it?
by robin
Sat Mar 16, 2019 1:37 pm
Forum: Resins
Topic: Solus Wax not sticking to build plate
Replies: 4
Views: 280

Re: Solus Wax not sticking to build plate

thanks, I'll give that a go. I had some luck yesterday by scratching the build plate with emery paper and then using the lattice support Yep, I was going to suggest that. I read it when setting up my Solus the first time and THANKFULLY, I've never had my prints fall off the plate. I don't use the S...
by robin
Sat Mar 16, 2019 1:28 pm
Forum: Resins
Topic: B9 Yellow Castable Resin Testing
Replies: 39
Views: 18770

Re: B9 Yellow Castable Resin Testing

Has this resin been proven reliable in the Solus these days? I remember in the beginning people were complaining about it sticking to the film, etc. It seems like this stuff is more cast-friendly than the Emerald or even the Cherry. Am I thinking in the right direction? Hi, Did you had a chance to ...
by robin
Wed Mar 06, 2019 1:23 pm
Forum: Help and Troubleshooting
Topic: Drop in intensity on infocus projector
Replies: 12
Views: 1870

Re: Drop in intensity on infocus projector

If you hear too much noises while printing, try lowering the z-lift speed when printing large pieces like that. b9 resins (especially yellow and emerald) are really sticky.
by robin
Tue Feb 26, 2019 7:19 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 59
Views: 4524

Re: ResinWorks EasyCastHD castable resin

rsaldivar wrote:does the brow have wax in it ?


No. It seems to be hard plastic, similar to B9's Red resin if you're familiar with it.
by robin
Thu Feb 21, 2019 10:25 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 59
Views: 4524

Re: ResinWorks EasyCastHD castable resin

Not sticky at all. It's a really good resin. I suggest printing at 42xy build area with it for best results. Haven't had a single bad print or bad casting. It's miles better than the emerald and easier to post cure. Just cure in water for 30min - 1 hour under UV. Or for better results in glycerin o...
by robin
Thu Feb 21, 2019 1:39 pm
Forum: Software
Topic: Contour Feature Requests
Replies: 18
Views: 5679

Re: Contour Feature Requests

I tried merging two scene files but it placed both models on top of each other. Is there a way to automatically have Contour rearrange the models on the plate?
by robin
Thu Feb 21, 2019 1:36 pm
Forum: Help and Troubleshooting
Topic: How to support this ring?
Replies: 3
Views: 440

Re: How to support this ring?

You have to add supports to all the prongs even if it doesn't show "green" in the Contour software. Also, lower the z-lift speed to 75 or less for such delicate prints.