Thank you.
So after checking all 4 corners
1. raise platform by +10
2. remove platform.
3. Run homing
Search found 44 matches
- Sun Sep 10, 2017 10:09 am
- Forum: Help and Troubleshooting
- Topic: Calibrating the build platform
- Replies: 3
- Views: 8109
- Sat Sep 09, 2017 7:32 pm
- Forum: Help and Troubleshooting
- Topic: Calibrating the build platform
- Replies: 3
- Views: 8109
Calibrating the build platform
Video below does not really show how to end built table calibration process. https://reify3d.wistia.com/medias/j9n1qcpjo8 At the very end when all corners where snug tight, I end up lifting platform up by +1 then removing build platform then moving by -1 down and then presses move to home position. ...
- Fri Jul 07, 2017 9:57 am
- Forum: General
- Topic: vivitek h1186 replacement lamp europe
- Replies: 0
- Views: 4857
vivitek h1186 replacement lamp europe
vivitek h1186 replacement lamp
Does anyone know where to buy replacement bulbs for Vivitek projector ? Preferable UK ?
Thanks
Does anyone know where to buy replacement bulbs for Vivitek projector ? Preferable UK ?
Thanks
- Fri Jun 09, 2017 4:29 pm
- Forum: Casting
- Topic: Casting resins cherry, emerald
- Replies: 50
- Views: 111626
Re: Casting resins cherry, emerald
I have used cheap UV nail curing box plus microware method, no luck. Last time I did casting I used envisionTEC othoflash curing unit. Went for about 8000 flashes when ET recommend 1000 and result was the same. I gave some pieces to the local casting factory to cast and they managed to cast really w...
- Fri Jun 09, 2017 1:48 pm
- Forum: Help and Troubleshooting
- Topic: What causes this line in growing
- Replies: 4
- Views: 8219
Re: What causes this line in growing
I have the same problem! Could someone explain please, thanks.
- Fri Jun 09, 2017 1:46 pm
- Forum: Casting
- Topic: Casting resins cherry, emerald
- Replies: 50
- Views: 111626
Re: Casting resins cherry, emerald
Thank you Archem,
I do use large furnace too, you can find some images attached on this thread above. How fast your furnace raise temperature ? Do you keep your flask hole facing down ? Do you let flask to touch furnace floor?
I do use large furnace too, you can find some images attached on this thread above. How fast your furnace raise temperature ? Do you keep your flask hole facing down ? Do you let flask to touch furnace floor?
- Thu Jun 08, 2017 9:00 pm
- Forum: Casting
- Topic: Casting resins cherry, emerald
- Replies: 50
- Views: 111626
Re: Casting resins cherry, emerald
Dipen , please do let me know what kind of result you going to get from your Argenta furnace. I have friend who tried casting several time using argenta furnace, but result were no good !
How many of you do pump extra air into a kiln, would be good to know?
How many of you do pump extra air into a kiln, would be good to know?
- Thu Jun 08, 2017 3:36 pm
- Forum: Casting
- Topic: Casting resins cherry, emerald
- Replies: 50
- Views: 111626
Re: Casting resins cherry, emerald
Gtg330 do you have any pictures of your castings to share ?
I have tried everything, only thing I'm thinking now is I need extra air flow in my kiln, or my kiln does not reach required temperature for resin fully to burn. Does any of you know how to check temperature inside the kiln ?
Thanks,D
I have tried everything, only thing I'm thinking now is I need extra air flow in my kiln, or my kiln does not reach required temperature for resin fully to burn. Does any of you know how to check temperature inside the kiln ?
Thanks,D
- Thu Jun 08, 2017 3:30 pm
- Forum: Resins
- Topic: Pre orders for New Solus Castable resin?
- Replies: 0
- Views: 5921
Pre orders for New Solus Castable resin?
JCK is here! When new castable resin will be available to pre order ?
Thanks,
Thanks,
- Sun Jun 04, 2017 9:05 pm
- Forum: Help and Troubleshooting
- Topic: Solus makes squeaky sound
- Replies: 8
- Views: 12539
Re: Solus makes squeaky sound
This is how it was suported. I have also tried print it on a 45 degree angle, but overhanded corner always gets shifted. I believe is due to sucksion forces.