Search found 29 matches
- Thu Aug 01, 2019 5:32 pm
- Forum: Help and Troubleshooting
- Topic: Quartz Detached from Printer
- Replies: 10
- Views: 21761
Re: Quartz Detached from Printer
Greatly appreciated! I'll pick up some 3mm tape for the fix.
- Thu Aug 01, 2019 4:11 am
- Forum: Help and Troubleshooting
- Topic: Quartz Detached from Printer
- Replies: 10
- Views: 21761
Re: Quartz Detached from Printer
Thank you! Is there a specific kind/brand of tape i should use?
- Thu Aug 01, 2019 1:20 am
- Forum: Help and Troubleshooting
- Topic: Quartz Detached from Printer
- Replies: 10
- Views: 21761
Re: Quartz Detached from Printer
I have an overhead ceiling fan that I turn on while printing. I haven't used a small fan blowing directly, and in close proximity, to the printer in order to avoid unnecessary dust/hair/etc flowing into the printer, onto the window, or onto the projector lens. That being said, if the separation was ...
- Sat Jul 27, 2019 9:59 pm
- Forum: Help and Troubleshooting
- Topic: Quartz Detached from Printer
- Replies: 10
- Views: 21761
Re: Quartz Detached from Printer
Hey,
Just as an update, the print I ran was successful (Thankfully! - It was a very important print).
Just as an update, the print I ran was successful (Thankfully! - It was a very important print).
- Sat Jul 27, 2019 7:42 pm
- Forum: Help and Troubleshooting
- Topic: Quartz Detached from Printer
- Replies: 10
- Views: 21761
Quartz Detached from Printer
Hey all, I went to set up a print today and noticed that the Quartz piece was slightly detached from the printer - it had slid about 5mm to one side. I have no idea how this happened - I genuinely take car of the printer. I slid the Quartz piece back to center, the glue/adhesive was slightly gummy s...
- Sat May 11, 2019 9:37 pm
- Forum: Software
- Topic: Contour Activation
- Replies: 1
- Views: 8689
Contour Activation
Hey! I tried contacting Reify through the contact page on the website but haven't heard back in 2 weeks, so I figured posting here may be quicker. I hadn't run my printer in a few months and recently went back to test out a few prints. I updated the laptop I use to run the printer, tried to open Con...
- Sat Oct 20, 2018 1:49 am
- Forum: Help and Troubleshooting
- Topic: Jagged Geometry In Contour
- Replies: 4
- Views: 7300
Re: Jagged Geometry In Contour
I appreciate the help! Using a value of 0.005 made the model acceptably smooth. For some reason, Matrix was defaulting with a value of 0.0.
- Sat Oct 20, 2018 12:39 am
- Forum: Help and Troubleshooting
- Topic: Jagged Geometry In Contour
- Replies: 4
- Views: 7300
Re: Jagged Geometry In Contour
Thanks for the reply. Honestly, I'm unfamiliar with adjusting Matrix settings/tolerances. Is there a specific tolerance I need to adjust? Is there a specific value I should set? And are these tolerances adjusted as I'm saving the file as an STL in Matrix?
Thanks again!
Thanks again!
- Fri Oct 19, 2018 10:47 pm
- Forum: Help and Troubleshooting
- Topic: Jagged Geometry In Contour
- Replies: 4
- Views: 7300
Jagged Geometry In Contour
Hey all, It's been a while since I've used my Solus printer. I opened up Contour today and updated it. I then imported an STL file and noticed some odd geometry that isn't apparent/present on the ring in Matrix. I imported a different ring and the same thing was happening. It never used to do this s...
- Thu Nov 02, 2017 5:19 am
- Forum: Help and Troubleshooting
- Topic: Unknown Print Flash/Film
- Replies: 11
- Views: 16921
Re: Unknown Print Flash/Film
Is opening up the printer a straightforward process? Anything I should take extra precaution doing? And is alcohol safe on both the mirror and underside of the quartz?