Search found 53 matches

by Dstonic
Mon Nov 12, 2018 6:00 pm
Forum: Hardware
Topic: Infocus projector bulbs.
Replies: 6
Views: 1422

Re: Infocus projector bulbs.

Here is a post I did on bulb replacement for my Vivitek .....you are correct it is really easy. The back of the bulb is deeply engraved and not ink stamped.
viewtopic.php?f=11&t=1179
by Dstonic
Mon May 21, 2018 6:18 pm
Forum: Casting
Topic: Problem with sucessfull casting
Replies: 8
Views: 2933

Re: Problem with sucessfull casting

[quote="Jewelermdt"]That fast of ramp most likely cause the Proto wax to boil and cause investment breakdown. The spur you have inside of the ring of the resin model, is that wax or resin. If wax it needs a way to melt out before the resin burns out. You would need to run it to the button....
by Dstonic
Fri May 18, 2018 1:35 pm
Forum: Casting
Topic: Problem with sucessfull casting
Replies: 8
Views: 2933

Re: Problem with sucessfull casting

Opti Cast investment....100:38 ratio...flask set time 5+ hrs....burn cycle is ramp 9999 to 1400 degrees 4.5 hrs then ramp down 675 degrees per hr to 850 degrees casting temp. The B9 did better than Protowizard..... thinking the proto could not handle this ramp cycle? My investment is too old? Three ...
by Dstonic
Wed May 09, 2018 9:58 pm
Forum: Casting
Topic: Whitegold - Castings with emerald resin
Replies: 28
Views: 9190

Re: Whitegold - Castings with emerald resin

Thought to refresh our continued Superior success using the Solus printer. Emil, you and your company are the best. We cast at 1400°(ramp 9999 on the controller) full blast straight in the furnace after the flask sets 5 hrs in Opti Cast....ramp down 650°per hour then cast at 850°. How in the heck d...
by Dstonic
Wed May 09, 2018 9:45 pm
Forum: Gallery
Topic: ***Totally Stoked!!***
Replies: 381
Views: 112770

Re: ***Totally Stoked!!***

Mark, really fine work you are doing. Appreciate how you share your success.
by Dstonic
Fri May 04, 2018 4:19 pm
Forum: Casting
Topic: Whitegold - Castings with emerald resin
Replies: 28
Views: 9190

Re: Whitegold - Castings with emerald resin

Thought to refresh our continued Superior success using the Solus printer. Emil, you and your company are the best. We cast at 1400°(ramp 9999 on the controller) full blast straight in the furnace after the flask sets 5 hrs in Opti Cast....ramp down 650°per hour then cast at 850°. How in the heck do...
by Dstonic
Sat Apr 28, 2018 7:50 pm
Forum: Help and Troubleshooting
Topic: Lamp Replacement
Replies: 5
Views: 1522

Re: Lamp Replacement

Is that the same bulb as the original? Thank you. Yes. I want to make it clear to all that is reading my response to you in this post, that I replaced the lamp with a OEM of what was in there before. Don't be fooled and just buy any ole lamp from a website...they may be "Knock Off's". The...
by Dstonic
Sat Apr 28, 2018 7:39 pm
Forum: Help and Troubleshooting
Topic: Lamp Replacement
Replies: 5
Views: 1522

Re: Lamp Replacement

How old is your printer? Didn't think you had yours that long. How many hours did you have on it? Mine is about 2 1/2 years old. Haven't looked at the hours in a while. Granted I didn't use it a lot when I first got it, but now it's used all the time. Not this week cause I'm waiting for a new tilt ...
by Dstonic
Fri Apr 27, 2018 9:14 pm
Forum: Help and Troubleshooting
Topic: Lamp Replacement
Replies: 5
Views: 1522

Lamp Replacement

Hey All, I just wanted to share something that has happened to me, and that was a projector lamp reaching its end. The UV was not producing anymore so it was time for a replacement. What I wish to share with you is "Where to get a new lamp"...."Take down and replacement with a new lam...
by Dstonic
Tue Apr 17, 2018 11:55 pm
Forum: General
Topic: Calibrating Build Plate -- what kind of paper to use?
Replies: 13
Views: 6451

Re: Calibrating Build Plate -- what kind of paper to use?

Can't seem to locate the video of the grow plate calibration.