Search found 787 matches
- Mon Jan 17, 2022 2:48 pm
- Forum: Tips and Tutorials
- Topic: Solus Pro user manual?
- Replies: 13
- Views: 23067
Re: Solus Pro user manual?
There is a way. Under File I think. Connect to printer. Not at store to look.
- Wed Aug 18, 2021 1:45 am
- Forum: Help and Troubleshooting
- Topic: Z-Axis Rail Wobble
- Replies: 2
- Views: 5023
Re: Z-Axis Rail Wobble
I take it this the older Solus printer, not the Solus Pro? Are the rods clean of grease build up. Sounds like something is binding. Did you run the calibration program?
- Wed Aug 18, 2021 1:40 am
- Forum: Casting
- Topic: CAST HELP ASAP PLS!!!!!!!! NEW TO CASTING
- Replies: 17
- Views: 31317
Re: CAST HELP ASAP PLS!!!!!!!! NEW TO CASTING
Most of my problems is I heat the metal too hot. This will cause pits, hole in your casting. I let the investment sit at least 5 hours. I get better results if I let them sit overnight before putting in oven. Especially with fine detail and lettering. I use a Necraft oven with a add on controller. V...
- Wed Jul 14, 2021 4:19 am
- Forum: Help and Troubleshooting
- Topic: Solus Contour Grows
- Replies: 1
- Views: 4784
Re: Solus Contour Grows
The projector is the problem IMO. How many hours on the bulb? But my guess is it's not the bulb but something internal. Contact Emil.
Bite the bullet and get the New Solus Pro machine.
Bite the bullet and get the New Solus Pro machine.
- Wed Jul 14, 2021 4:15 am
- Forum: Casting
- Topic: CAST HELP ASAP PLS!!!!!!!! NEW TO CASTING
- Replies: 17
- Views: 31317
Re: CAST HELP ASAP PLS!!!!!!!! NEW TO CASTING
Try a different resin. Solus Wax Pro cast great. Looks like interaction with the investment. Do you go to 1400 degrees and hold that for at least 3 hours.
- Mon Feb 22, 2021 4:37 am
- Forum: Help and Troubleshooting
- Topic: Solus Contour Pro
- Replies: 3
- Views: 8877
Re: Solus Contour Pro
How close are you zoomed in using Contour software? If you are zoomed in it will not show the supports. Did your computer do a windows update? Mine wanted to update a week or so ago. Might have changed the graphics drivers. It does sound like a graphics problem.
- Mon Oct 26, 2020 5:21 pm
- Forum: Help and Troubleshooting
- Topic: Warped print/how to support this?
- Replies: 5
- Views: 11055
Re: Warped print/how to support this?
increase you touch point size. Maybe add them manual. One on each side of ring up to oval area. 2mm wide support with .6 to .8 touch points.
- Tue Jun 23, 2020 3:18 am
- Forum: Help and Troubleshooting
- Topic: Z Motor Problem
- Replies: 4
- Views: 11115
Re: Z Motor Problem
glad you figured it out. If you have a laser welder just weld the wire back.
- Sun Jun 21, 2020 3:39 am
- Forum: Help and Troubleshooting
- Topic: Z Motor Problem
- Replies: 4
- Views: 11115
Re: Z Motor Problem
I would check that the switch is ok. One time the board cracked and switch would not work correctly. Also make sure the plugs are seated correctly and you didn't mix up where they plug into the board.
- Thu Jun 18, 2020 3:30 am
- Forum: Resins
- Topic: So what is up with SolusWax Pro?
- Replies: 33
- Views: 65228
Re: So what is up with SolusWax Pro?
I know it's not recommended but I leave my vat on the printer with the resin in it. I cover it with a piece of cardboard and on top of the cardboard are some packets of silica gel absorbent. I just stir it up with the spatula and start printing.