Search found 25 matches

by emild
Thu Jan 31, 2019 9:56 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 62
Views: 6919

Re: ResinWorks EasyCastHD castable resin

I have a big question:

burnout chedule have a 2C per minunte. All ramp have 2 C per minute for option 2... but if you calculate will not reach the temperatures??

can anyone make clear ?

is 2C per minute for option 1 burnout or for both burnout options?

Thank you
by emild
Wed Jan 30, 2019 8:08 pm
Forum: Casting
Topic: yellow gold casting - "new" burnout
Replies: 6
Views: 2610

Re: yellow gold casting - "new" burnout

We use a master alloy from Legor, and add palladium to get 15 % of palladium in our alloy. For Whitegold we use 1300 °C. ( flasks 500 °C - (we found out, that the combination of high temperatured melt and low the low temperature of the flask are optimal. palladium shrinks a lot, so we get really aw...
by emild
Fri Jan 25, 2019 5:03 pm
Forum: Casting
Topic: Whitegold - Castings with emerald resin
Replies: 28
Views: 9823

Re: Whitegold - Castings with emerald resin

Kristian

Thank you for for informations,
It is a really, really great


Thank you again
by emild
Wed Jan 23, 2019 12:03 am
Forum: Hardware
Topic: Projector "Lens Shift" Tight
Replies: 5
Views: 3157

Re: Projector "Lens Shift" Tight

Mikkopee wrote:Yes, I have this same issue!
Just recieved my projector via Jordi from Micron3D.
I wonder if there is some kind f lock somewhere..?


Anyone found?
by emild
Mon Jan 21, 2019 10:37 pm
Forum: Help and Troubleshooting
Topic: Problems with print
Replies: 7
Views: 676

Re: Problems with print

25 micron XY setup puts out a little more energy since the projector is closer, so that makes sense. Just adjust the intensity down a bit and it should be ok. I do suggest printing at 42xy, because you get a large build area and the print quality is nearly the same unless you print really small det...
by emild
Mon Jan 21, 2019 10:36 pm
Forum: Help and Troubleshooting
Topic: Problems with print
Replies: 7
Views: 676

Re: Problems with print

25 micron XY setup puts out a little more energy since the projector is closer, so that makes sense. Just adjust the intensity down a bit and it should be ok. I do suggest printing at 42xy, because you get a large build area and the print quality is nearly the same unless you print really small det...
by emild
Mon Jan 21, 2019 8:59 pm
Forum: Help and Troubleshooting
Topic: Problems with print
Replies: 7
Views: 676

Re: Problems with print

mongerdesigns wrote:Also, which projector do you have?

Last week worked good. I printed with 42 resolution and aftet that changed to 25 and that s happenend
by emild
Mon Jan 21, 2019 4:12 pm
Forum: Help and Troubleshooting
Topic: Shifting layers at top of finger rail
Replies: 17
Views: 4722

Re: Shifting layers at top of finger rail

I checked the quartz and it didn't slide around. I replaced the film and made sure there were no air pockets and it lays perfectly flat. These are better and I definitely usable, but it is still not %100. The layer shift still seems to be there. :| attached are images showing supported and un-suppo...
by emild
Mon Jan 21, 2019 3:31 pm
Forum: Help and Troubleshooting
Topic: Problems with print
Replies: 7
Views: 676

Problems with print

I ahve some issue with the printing... is giving me layera and bad surface on the prints
by emild
Mon Jan 21, 2019 2:06 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 62
Views: 6919

Re: ResinWorks EasyCastHD castable resin

No, but I think you should spend some time reading the past threads, because all these questions you're asking where discussed in here before. can you send me to a post that is real good for best curring for emerald. i receive the easycast HD only friday and i need badly to test on emerald some cas...