Search found 293 matches

by rsaldivar
Tue Apr 09, 2019 3:07 pm
Forum: Help and Troubleshooting
Topic: Printing and supports
Replies: 10
Views: 1874

Re: Printing and supports

well Id say use a hairdryer to warm up the resin in the vat , then mix very well in the vat with a spatula , use very thick supports .6 maybe (with SW always thicker supports than normal ) , and it wouldn't hurt to put the lattice on the base , make sure to use the gel , and if you don't have any, s...
by rsaldivar
Thu Mar 28, 2019 4:54 pm
Forum: Resins
Topic: nylon resin
Replies: 0
Views: 729

nylon resin

Hi Emil , would this resin work on the solus ? and if so , how detail do you think ? i know it say made for 30z , but how would it copare to 30z in solcast for example ? if I got some would you help with the profile ?

https://shop.b9c.com/rugged-nylon6
by rsaldivar
Tue Mar 26, 2019 6:27 pm
Forum: General
Topic: anyone selling a used oven in the usa ?
Replies: 0
Views: 718

anyone selling a used oven in the usa ?

anyone selling a used oven in the usa ?
by rsaldivar
Mon Mar 25, 2019 6:56 pm
Forum: Help and Troubleshooting
Topic: Printing and supports
Replies: 10
Views: 1874

Re: Printing and supports

thats resin looks like soulcast not soulwax ??
by rsaldivar
Fri Mar 08, 2019 9:52 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 11785

Re: ResinWorks EasyCastHD castable resin

finished
by rsaldivar
Fri Mar 08, 2019 9:43 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 11785

Re: ResinWorks EasyCastHD castable resin

its as you said , some holes filled , so had to redrill them out , outside of that , every other spot came out perfectly , those filled holes I believe are what happens to letters when you try and cast fonts , in this case just redrill but if they would be fonts , then maybe have to recast and do ex...
by rsaldivar
Thu Mar 07, 2019 5:42 am
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 11785

Re: ResinWorks EasyCastHD castable resin

that was my fist time growing and casting it , I did a 45 min. boil in water anniel , a 10 min. uv cure , 2 hours sit time with optima and a straight ramp to 1500 f for a total time in the oven of 6 hours , down to cast temp and this is my results , will try different thing next time , I wanted to s...
by rsaldivar
Thu Mar 07, 2019 5:35 am
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 11785

Re: ResinWorks EasyCastHD castable resin

so I made this , one with the holes cut threw and one without , just to see what would cast better , 18ky
by rsaldivar
Thu Mar 07, 2019 5:28 am
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 11785

Re: ResinWorks EasyCastHD castable resin

hasd81 just a guess, based on what Iv seen , that looks to me as too high a temp. in the burnout cycle or too long a time at the high temp , Also the only other thing I think it could be is that your guy is using boric acid water and that sometimes happens when you use that , however castings usuall...
by rsaldivar
Fri Mar 01, 2019 5:23 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 11785

Re: ResinWorks EasyCastHD castable resin

where are the pics of castings to this , I see very little of them