Search found 40 matches
- Mon Nov 13, 2017 1:55 pm
- Forum: Help and Troubleshooting
- Topic: prints just started failing
- Replies: 16
- Views: 24148
prints just started failing
Hi, can anyone explain why my prints just started failing and also why I've started to get the resin curing at the bottom of the tray. Everything was printing fine last week then 1st print failed, I cleared out the resin tray and sieved the resin, put on another print and hey presto!...the same thin...
- Sat Oct 14, 2017 9:26 am
- Forum: Help and Troubleshooting
- Topic: Teardrop pendant warped
- Replies: 5
- Views: 10220
Re: Teardrop pendant warped
Hi,
I printed 2 models and they were front to back. I have Solus Contour but I always make my supports in Matrix. The supports were .4mm thick and the distance to the 1st point of contact was 2mm. I'll make the supports wider on the next print and also give them a taper. Will post results later.
I printed 2 models and they were front to back. I have Solus Contour but I always make my supports in Matrix. The supports were .4mm thick and the distance to the 1st point of contact was 2mm. I'll make the supports wider on the next print and also give them a taper. Will post results later.
- Thu Oct 12, 2017 1:03 pm
- Forum: Help and Troubleshooting
- Topic: Teardrop pendant warped
- Replies: 5
- Views: 10220
Teardrop pendant warped
Hi all,
Can anyone explain why this pendant has warped? are my supports too thin? is the pendant too heavy and would angling it slightly make any difference? This is the 4th print on this pendant and it's happened every time.
Can anyone explain why this pendant has warped? are my supports too thin? is the pendant too heavy and would angling it slightly make any difference? This is the 4th print on this pendant and it's happened every time.
- Mon Jan 23, 2017 10:16 am
- Forum: Help and Troubleshooting
- Topic: Bendy Print
- Replies: 9
- Views: 13724
Re: Bendy Print
Thanks, I'll try the tilting method 1st!
- Wed Jan 18, 2017 5:14 pm
- Forum: Help and Troubleshooting
- Topic: Bendy Print
- Replies: 9
- Views: 13724
Re: Bendy Print
Thanks for that, The base is .4mm thick, but I'll take the suggestions on board. i was really wondering about the claws bending away? i presumed I'd done something wrong!
- Wed Jan 18, 2017 11:42 am
- Forum: Help and Troubleshooting
- Topic: Bendy Print
- Replies: 9
- Views: 13724
Re: Bendy Print
Here you go.
- Tue Jan 17, 2017 4:03 pm
- Forum: Help and Troubleshooting
- Topic: Bendy Print
- Replies: 9
- Views: 13724
Bendy Print
Hi,
Can anyone tell me why the base is bending to the left and the claws have a slight bend away to the right on this print? could it be gravity that's causing them to bend away from the model as i grew it on its side?
Can anyone tell me why the base is bending to the left and the claws have a slight bend away to the right on this print? could it be gravity that's causing them to bend away from the model as i grew it on its side?
- Fri Jan 06, 2017 2:39 pm
- Forum: Help and Troubleshooting
- Topic: printing lines
- Replies: 3
- Views: 6307
Re: printing lines
Thanks, I'll loosen them off slightly and see how the next prints pan out.
- Thu Jan 05, 2017 3:01 pm
- Forum: Help and Troubleshooting
- Topic: printing lines
- Replies: 3
- Views: 6307
printing lines
Hi,
Just printed this ring and I have horizontal lines near the top of it. does anyone know why?
Cheers
Just printed this ring and I have horizontal lines near the top of it. does anyone know why?
Cheers
- Wed Oct 05, 2016 9:36 am
- Forum: Help and Troubleshooting
- Topic: Supports and Sprues
- Replies: 4
- Views: 7972
Re: Supports and Sprues
Thanks for the help everyone. The rings came out just fine following all the advice.