Search found 787 matches
- Fri Nov 06, 2015 1:56 am
- Forum: General
- Topic: Solus arrived!
- Replies: 20
- Views: 32236
Re: Solus arrived!
Don't think so. Be a pain to undo it from B9. Different setups.
- Tue Nov 03, 2015 2:55 am
- Forum: Tips and Tutorials
- Topic: Basic Support Structures Tutorials
- Replies: 17
- Views: 61205
Re: Basic Support Structures Tutorials
I've been having fun with a filigree also.
I would say your supports at the halo need to be a little bigger and out at the edge of the halo. Put supports in each angle change. also might help. So instead of three on each side, have five. That's what I would do.
I would say your supports at the halo need to be a little bigger and out at the edge of the halo. Put supports in each angle change. also might help. So instead of three on each side, have five. That's what I would do.
- Tue Nov 03, 2015 2:47 am
- Forum: General
- Topic: Solus arrived!
- Replies: 20
- Views: 32236
Re: Solus arrived!
You should be ok with both plunged in. I would be sure the one I'm not using is turned off. You connect the the Solus through CW. Your laptop will see the projector as another display which need to be set up correctly. This may be a problem where you have to dis-connect the B9 projector. Unless you ...
- Mon Nov 02, 2015 1:37 am
- Forum: Gallery
- Topic: Getting Started First Day With the Solus (Prints)
- Replies: 8
- Views: 14343
Re: Getting Started First Day With the Solus (Prints)
Great prints. I am struggling with mine. Appreciate showing the supports. I need to practice with the Matrix support tools.
- Thu Oct 29, 2015 1:46 am
- Forum: Tips and Tutorials
- Topic: Questions About Basic Calibration
- Replies: 8
- Views: 15950
Re: Questions About Basic Calibration
It's mostly adjusting the focus and zoom on the projector so the gird measures to your Build size. Before you put down paper on the quartz, make sure the lines of the grid do NOT go down the sides of the quartz table. It the paper is on top you don't see this and could be off in your measurements. W...
Re: Ups's
Also helps if you get a lot of thunderstorms. Will keep the printer running through those flickers and spikes. Spikes can kill machines.
- Fri Oct 23, 2015 3:20 am
- Forum: General
- Topic: Finialy printing again
- Replies: 11
- Views: 20017
Finialy printing again
Finlay got back to printing after breaking my quarts table. Got the new one in and somehow my build platform walked off. Had to wait for that to get in. Got it yesterday but was too busy to get things going. So today got the build plate flat to the table and tried a ring. It printed the bottom great...
- Tue Oct 20, 2015 12:32 am
- Forum: Tips and Tutorials
- Topic: Procedure or Check List for 25 to 41 and back again.
- Replies: 26
- Views: 44016
Re: Procedure or Check List for 25 to 41 and back again.
Got it
Thanks
Hope to be printing again soon. Received notice my build platform was sent. Still don't know what happened to mine. Just waked off.
Thanks
Hope to be printing again soon. Received notice my build platform was sent. Still don't know what happened to mine. Just waked off.
- Mon Oct 19, 2015 2:21 am
- Forum: Hardware
- Topic: Link me to a laptop!
- Replies: 6
- Views: 12955
Re: Link me to a laptop!
The cable you need will come with the printer, projector.
- Sun Oct 18, 2015 1:43 am
- Forum: Tips and Tutorials
- Topic: Procedure or Check List for 25 to 41 and back again.
- Replies: 26
- Views: 44016
Re: Procedure or Check List for 25 to 41 and back again.
Bump Any headway on this??
Thanks
Mike
Thanks
Mike