Search found 70 matches
- Wed Feb 15, 2017 11:23 am
- Forum: Casting
- Topic: Success curing and casting Emerald green resin
- Replies: 33
- Views: 53869
Re: Success curing and casting Emerald green resin
You say you remove the cap. Are you talking about the rubber base that the flask sets in?
- Mon Feb 13, 2017 10:06 pm
- Forum: Casting
- Topic: Casting Emerald Wax Problems
- Replies: 20
- Views: 34523
Re: Casting Emerald Wax Problems
I don't think your burnout cycle is long enough. my burnout takes 9 to ten hours with three hours at 1350. If i am casting something where i can't afford to make a mistake i use phosphate bonded investment. If you're only taking 1.5 hours to 1400 F I think the expanding resin is causing bits of the ...
- Mon Feb 13, 2017 3:10 am
- Forum: General
- Topic: Problem with projector
- Replies: 4
- Views: 8482
Re: Problem with projector
I was able to print 4 times succesfully since replacing the bulb and each time the printer turned off after printing. The fifth time the projector did not turn off. when I attempted to close the program,I got a message asked if i really wanted to close the program, the print is not completed. I defi...
- Sat Feb 11, 2017 1:15 pm
- Forum: General
- Topic: Problem with projector
- Replies: 4
- Views: 8482
Re: Problem with projector
Thanks Mark; I replaced my HDMI cable and the new bulb is working.
- Fri Feb 10, 2017 1:29 pm
- Forum: General
- Topic: Problem with projector
- Replies: 4
- Views: 8482
Problem with projector
I just installed a new bulb in my projector. I have an infocus 8606 HD. I can,t tell if the lamp is working or not. When the projector is turned on is the red led supposed to be on? When the projector is attached to the printer and I press the menu button on the remote control, the menu is displayed...
- Tue Feb 07, 2017 3:08 pm
- Forum: General
- Topic: Projector doesn't always turn off.
- Replies: 1
- Views: 4480
Projector doesn't always turn off.
My projector doesn't always turn off. I thought maybe I was forgetting to check the box in the program so I stuck a message right on my screen. It isn't that. This wouldn't be a big problem because I call my wife and have her check it and turn it off if it's still on. Unfortunately I think she must ...
- Tue Feb 07, 2017 11:53 am
- Forum: General
- Topic: Infocus 8606 lamp blown
- Replies: 1
- Views: 4464
Infocus 8606 lamp blown
I think my projector bulb is blown. Infocus 8606 HD. I see you can buy just the bulb or you can buy with the whole housing. What do you recommend? Also, I find when searching for the bulb the Canadian suppliers say no longer available. Anybody know if this projector is still in production?
- Thu Feb 02, 2017 1:16 pm
- Forum: General
- Topic: projector not initialized message
- Replies: 2
- Views: 6130
Re: projector not initialized message
When I have this problem I just pull out the two usb cables and reconnect them. If that doesn't work I close the program and re stare the computer.
- Wed Jan 25, 2017 9:56 pm
- Forum: Help and Troubleshooting
- Topic: How to adjust scale in the z direction
- Replies: 1
- Views: 4069
How to adjust scale in the z direction
I managed to get a lovely print after i increased the exposure time, changed the film again and put new resin. The print was wonderful but the scale was off in all three axes. I think the x and y I can adjust but How to adjust the z, i haven't a clue. For now, I sdjusted the scale on the model to se...
- Tue Jan 24, 2017 9:16 pm
- Forum: Help and Troubleshooting
- Topic: How to adjust the exposure time etc. in contour?
- Replies: 3
- Views: 6196
Re: How to adjust the exposure time etc. in contour?
I'm guessing I have less than 500 hours on the lamp. Thanks by the way.