Search found 46 matches
- Sun Feb 25, 2018 7:52 pm
- Forum: Help and Troubleshooting
- Topic: Sample files for print?
- Replies: 27
- Views: 37045
Re: Sample files for print?
I'll give it a shot.
- Sun Feb 25, 2018 6:53 pm
- Forum: Help and Troubleshooting
- Topic: Sample files for print?
- Replies: 27
- Views: 37045
Re: Sample files for print?
1 thing I forgot to mention was that before I put the resin in I did put the tank on the quartz to see how tight it felt compared to my old acrylic tank. I noticed that the quartz has a very slight give from side to side when I moved the tank around. It did come off around 6 months back. I put it ba...
- Sun Feb 25, 2018 6:29 pm
- Forum: Help and Troubleshooting
- Topic: Sample files for print?
- Replies: 27
- Views: 37045
Re: Sample files for print?
Best guess is 3-400 hours.
Email sent.
Email sent.
- Sun Feb 25, 2018 5:21 pm
- Forum: Help and Troubleshooting
- Topic: Sample files for print?
- Replies: 27
- Views: 37045
Lines in Print and Sag
Thank you. I've got a test print done with a SolusCast sample I have. I'm trying to iron out all the issues before I get on with Proto for work stuff. I think it looks pretty good but seems to have multiple problems that might have been causing my previous prints to fail. This print is with contour ...
- Tue Feb 20, 2018 7:56 pm
- Forum: Help and Troubleshooting
- Topic: Sample files for print?
- Replies: 27
- Views: 37045
Sample files for print?
Hi all,
I just got my aluminum tank with some solus resin. To narrow down any user error I want to try some prints where any failures can be more easily diagnosed.
Where are the sample files(contour) located to do test prints? I only have links to the manuals on dropbox in my original solus emails.
I just got my aluminum tank with some solus resin. To narrow down any user error I want to try some prints where any failures can be more easily diagnosed.
Where are the sample files(contour) located to do test prints? I only have links to the manuals on dropbox in my original solus emails.
- Tue Feb 20, 2018 5:53 pm
- Forum: General
- Topic: Can't print without lines on model
- Replies: 8
- Views: 15938
Re: Can't print without lines on model
Did this get solved?
- Sat Feb 03, 2018 3:58 pm
- Forum: Help and Troubleshooting
- Topic: Failed prints. Pulling my hair out!
- Replies: 25
- Views: 38297
Re: Failed prints. Pulling my hair out!
OpedHead, most likely supports. I guess meshing errors could cause problems too
- Sat Feb 03, 2018 12:34 am
- Forum: Help and Troubleshooting
- Topic: tilt plate gap
- Replies: 2
- Views: 5778
tilt plate gap
Should there be a gap on the left side between tilt plate and top surface? On the right side, it's flush, but on left there is slight gap. I'm not sure if it has always been there. I'm suddenly having problems getting attachment to build plate so looking it over.
- Wed Jan 31, 2018 11:40 pm
- Forum: Help and Troubleshooting
- Topic: Too many Mis prints
- Replies: 8
- Views: 12282
Re: Too many Mis prints
mongerdesigns wrote:This doesn't look like a film issue. Seems like not enough light is coming from the projector. Try increasing the exposure time by 1 second. See if that does anything.
What are you looking at that makes you think it could be lack of light? uniformity of failure?
- Sun Aug 06, 2017 3:11 am
- Forum: Software
- Topic: homing cycle doesn't work again
- Replies: 9
- Views: 13959
Re: homing cycle doesn't work again
It was the same behavior on all the ports. I'll secure back up computer just in case. cheers