Search found 41 matches
- Thu Dec 08, 2016 11:55 pm
- Forum: Help and Troubleshooting
- Topic: Need help BAD
- Replies: 11
- Views: 18112
Re: Need help BAD
Here are two more pics of failed prints I couldn't fit in the above post, and a pic of the 'working' resin container I use and strainer, in case these could be contributing Regarding the ring with the four tiny supports on the bottom. Please use the RING SUPPORT button and click on the ring to supp...
- Thu Dec 08, 2016 11:38 pm
- Forum: Help and Troubleshooting
- Topic: Need help BAD
- Replies: 11
- Views: 18112
Re: Need help BAD
The top flat print. Is that the bottom of the print? I see marks from the supports. Why not flip the model so you don't have to support the part with the text on it and print flat on the build table without any supports? The second image, the ring with text on it. You can see how one side of the ri...
- Sun Dec 04, 2016 8:19 am
- Forum: Help and Troubleshooting
- Topic: Need help BAD
- Replies: 11
- Views: 18112
Re: Need help BAD
Here are two more pics of failed prints I couldn't fit in the above post, and a pic of the 'working' resin container I use and strainer, in case these could be contributing
- Sun Dec 04, 2016 8:01 am
- Forum: Help and Troubleshooting
- Topic: Need help BAD
- Replies: 11
- Views: 18112
Need help BAD
I need help BAD... I have been using my Solus at least 2 months now and I can not get accurate prints out of it, or even, consistent un accurate, but, un failed prints and I'm getting close to looking for refund unless I can get this sorted out soon as this is really messing with my business and pus...
- Wed Nov 16, 2016 3:33 pm
- Forum: Help and Troubleshooting
- Topic: Can I skip the first slice?
- Replies: 2
- Views: 4998
Re: Can I skip the first slice?
Ohh right with the move tool of course. It was doing my head in...Thank you!!!
- Wed Nov 16, 2016 2:51 pm
- Forum: Help and Troubleshooting
- Topic: Can I skip the first slice?
- Replies: 2
- Views: 4998
Can I skip the first slice?
I've checked all the slices and they're fine except the face that the first slice only has about 10% of the supports then the next slice has everything.
Is there a way I can just skip slice one or delete it in contour?
Or will one stray slice be ok and the print will be fine?
Is there a way I can just skip slice one or delete it in contour?
Or will one stray slice be ok and the print will be fine?
- Wed Nov 16, 2016 5:34 am
- Forum: Help and Troubleshooting
- Topic: Grid ratio out
- Replies: 4
- Views: 7634
Re: Grid ratio out
Thanks for your reply Sorry I know I'm posting about stuff I should already know and things which have been covered before somewhere in a tutorial but I can't seem to find them anywhere.. is there a manual I should have or a place all this info is centralised? I have been collating in folders (on pc...
- Sun Nov 13, 2016 12:55 pm
- Forum: Help and Troubleshooting
- Topic: Grid ratio out
- Replies: 4
- Views: 7634
Re: Grid ratio out
Ahhh finally found the trick. I've come across this before, but whenever I land in the video page, there are no videos in the "other" section until i close the menu and re open it again Thankyou the videos are a great resource, the adjusting grid video is good to know, but none of the grid...
- Sat Nov 12, 2016 11:52 am
- Forum: Help and Troubleshooting
- Topic: Grid ratio out
- Replies: 4
- Views: 7634
Grid ratio out
Hi everyone, When I go to measure the grid when calibrating the ratio is out. If I adjust it to 80mm wide it's only 44mm tall and then all my models are out. In all the instructions I could find, it only shows to adjust the the overall zoom and adjust the taper if it's distorted but not the ratio. I...
- Mon Sep 26, 2016 4:14 pm
- Forum: Help and Troubleshooting
- Topic: Need grid file for 42micron
- Replies: 2
- Views: 5494
Re: Need grid file for 42micron
Here is the grid: https://www.dropbox.com/s/e574csad4ayoyj5/80x45Grid.cws?dl=0 If you upgrade to Contour you just need to click a button :) Thanks Reify! So I've learn't. My apologies, I was using the manual to change from 25 to 42 micron which directed me to use Creation Workshop. I got onto the A...