Search found 73 matches
- Sun Sep 24, 2017 8:37 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
Yes 2 of the models look very bad,optical path is fine I think I cleaned everything although it feels like the quartz is a bit higher, when I put the vat on it I have push the vat slightly down to screw the thumbscrews in,I don't understand whats going on. Another thing my resin is almost finished m...
- Sun Sep 24, 2017 7:06 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
I did one print with both exposure times bumped up with 1 second and it was a mess for two of the rings one looked ok.
- Sun Sep 24, 2017 6:10 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
Thanks I will try and hope it will work.
- Sun Sep 24, 2017 4:33 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
Thanks for your reply but I have to add 1 second to both exposure times,like layer exposure is 2,7 now I should bring it to 3,7
and initial exposure i now 15 and I should bring it to 16?
and initial exposure i now 15 and I should bring it to 16?
- Sun Sep 24, 2017 7:40 am
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
I did this print maybe 4 times and every time,there are 3 rings on the build plate but every time the first one is good the second 60% of the ring printed and the last one 30% of ring printed and all 4 prints were the same is this a grid issue? Because I tried it with other resin also and it got sam...
- Wed Sep 20, 2017 7:34 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
I think you are right the bottle is almost finished maybe 90% used thats maybe the problem I remember when I got the new resin I did not
shaked and stirred the resin,thanks.
shaked and stirred the resin,thanks.
- Wed Sep 20, 2017 4:24 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
Thanks Drewbacca
These spacers is maybe a good idea,I will order them.
Berc
These spacers is maybe a good idea,I will order them.
Berc
- Wed Sep 20, 2017 4:07 am
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
Thanks Monger
I am getting this kind of prints lately,last 8 or 9 prints failed is this a resin problem.
I am getting this kind of prints lately,last 8 or 9 prints failed is this a resin problem.
- Tue Sep 19, 2017 10:28 pm
- Forum: Help and Troubleshooting
- Topic: So many failed prints
- Replies: 26
- Views: 38148
Re: So many failed prints
Hi,I have one more question,I hear a lot on this forum to enable the full rgb,I have a intel hd graphics card and I can't find anything about rgb,I founs something else but its not called rgb but has something to do with color spectrum is that the same?
- Tue Sep 19, 2017 7:02 am
- Forum: Help and Troubleshooting
- Topic: How I can get continuous success in print
- Replies: 14
- Views: 23059
Re: How I can continuously print successful
Where can I buy Tilers dip I am located in Europe,Ilike the smoothness of wax cast but casting is not too good