Search found 157 matches
- Wed Dec 21, 2016 11:34 pm
- Forum: Hardware
- Topic: Inexpensive UV Curing Chamber
- Replies: 23
- Views: 38329
Re: Inexpensive UV Curing Chamber
My green prints go from build table, rinse in tap water, ultrasonic in tape water, Nail UV box for 30mins (to an hour depending on how tied up I am with other things) in tap water. Perfect every time.
- Wed Dec 21, 2016 10:36 pm
- Forum: Software
- Topic: Parameter incorrect
- Replies: 8
- Views: 13238
Re: Parameter incorrect
Sent.
Please let me know what you find.
Thank you
Jim
Please let me know what you find.
Thank you
Jim
- Wed Dec 21, 2016 1:32 pm
- Forum: Software
- Topic: Parameter incorrect
- Replies: 8
- Views: 13238
Re: Parameter incorrect
Hey Reify,
Sorry for the delayed response. Christmas time is insane. I've been busy finishing the last of my orders that needed to be ship.When I get back in my shop later today that file will be sent.
Jim
Sorry for the delayed response. Christmas time is insane. I've been busy finishing the last of my orders that needed to be ship.When I get back in my shop later today that file will be sent.
Jim
- Tue Dec 20, 2016 12:45 am
- Forum: Software
- Topic: Parameter incorrect
- Replies: 8
- Views: 13238
Re: Parameter incorrect
So here's the funny thing. I tried slice preview before using the manual supports in Contour (automatic locked up my low power laptop) and it sliced perfectly. Then put in some manual supports and that's when the parameter error pops up. So, it has to be the supports in Contour.
- Mon Dec 19, 2016 12:00 pm
- Forum: Software
- Topic: Parameter incorrect
- Replies: 8
- Views: 13238
Re: Parameter incorrect
Yes, it does fit in the Contour print area. I'll take a screen shot and paste later today and also try to send the stl as well.
Thank you
Jim
Thank you
Jim
- Sun Dec 18, 2016 6:00 pm
- Forum: Software
- Topic: Parameter incorrect
- Replies: 8
- Views: 13238
Parameter incorrect
I'm trying to print a cuff but am getting a print fail parameter incorrect. I tried to slice preview but get the parameter incorrect error there as well. Not sure what the parameter is, but obviously it's incorrect. Anybody know what can be done? It's a large stl but I did run it through netfab and ...
- Sat Dec 03, 2016 3:52 am
- Forum: Hardware
- Topic: Grid Calibration
- Replies: 4
- Views: 10034
Grid Calibration
I'm getting all but the very top corners square but my major issue is while most all the sides and top are straight the bottom has a bow that I can not seem to get rid of without throwing everything else off.
- Tue Nov 22, 2016 6:16 pm
- Forum: Help and Troubleshooting
- Topic: Crystal moving
- Replies: 8
- Views: 12798
Re: Crystal moving
I agree, often times the small things (no pun) get overlooked. So I'm nearly 100% positive the issues with failed prints was the film being stretched from over tightening the 2 thumbscrews during the initial film install or when replacing the vat. I am a Solus newbie, I expect issues as I have no ex...
- Tue Nov 22, 2016 12:18 am
- Forum: General
- Topic: Cure Crazy
- Replies: 12
- Views: 19252
Re: Cure Crazy
Cure your prints in a clear glass or bowl of water. You will be amazed. Oxygen inhibits curing.
- Mon Nov 21, 2016 12:20 pm
- Forum: Help and Troubleshooting
- Topic: Crystal moving
- Replies: 8
- Views: 12798
Re: Crystal moving
Hello. Yes, I strain after printing if going to sit or has sat in the vat for more than a day. If the new resin in the bottle has been setting that get put on the magnetic stir, usually over 1 hour. The prints stick to the build table fine and start build fine but just tail off to nothing, stop buil...