Search found 36 matches
- Wed Apr 05, 2017 5:49 pm
- Forum: Help and Troubleshooting
- Topic: I'm disapointed With Solus
- Replies: 13
- Views: 20258
Re: I'm disapointed With Solus
To be frank I have experienced similar outcomes in I'd say the growing problem affects 1 in every 20 of my prints, but I am still happy with my solus. At one point I was printing 3 identical rings side by side knowing two might fail to grow. As I read the forums and educated myself I learned how to...
- Wed Apr 05, 2017 5:45 pm
- Forum: Help and Troubleshooting
- Topic: I'm disapointed With Solus
- Replies: 13
- Views: 20258
Re: I'm disapointed With Solus
I would bump it up by 0.2 seconds. Also if you can send me that scene file and I'll take a look at the supports. Thanks for Your suggestion. However, I successfully print that design without increasing exposure time. Can I increase exposure time from default 3.8second to 4second for my next print. :)
- Wed Apr 05, 2017 5:48 am
- Forum: Help and Troubleshooting
- Topic: I'm disapointed With Solus
- Replies: 13
- Views: 20258
Re: I'm disapointed With Solus
Is that the cherry resin? That piece might need more of an angle. Also are you using the default exposure times for the cherry? I see some signs of underexposure. You might need to bump up the exposure slightly. On complex pieces like that (with lots of holes that create overhangs at the corners), ...
- Tue Apr 04, 2017 4:49 pm
- Forum: Help and Troubleshooting
- Topic: I'm disapointed With Solus
- Replies: 13
- Views: 20258
I'm disapointed With Solus
I disappointed with Solus even though the surface quality is excellent but my headache is flat design as attached image show that even after placing huge support it is unsuccessful. I'm waiting for your valuable helpful comment.
Regard,
Kamal Soni
Regard,
Kamal Soni
- Thu Mar 30, 2017 6:42 am
- Forum: General
- Topic: What causes this....
- Replies: 3
- Views: 7667
What causes this....
Why 2 cube successfully print and with same support one failed?
- Wed Mar 29, 2017 7:00 am
- Forum: General
- Topic: How to center the Grid
- Replies: 12
- Views: 19678
Re: How to center the Grid
reify wrote:The mount is flexible so you can just bend it up a bit.
Thanks for reply, my first 42xy print failed, Why only supported item get failed, any issue with support.
- Tue Mar 28, 2017 4:36 pm
- Forum: General
- Topic: How to center the Grid
- Replies: 12
- Views: 19678
Re: How to center the Grid
Hi, Use the feet to raise the back of the projector until the grid is within the frame. If necessary, then use the keystone (buttons on the top of the projector or remote) to straighten the sides of the grid. When I raise the back of the projector, mount become free from two magnetic screw. Can I l...
- Tue Mar 28, 2017 1:07 pm
- Forum: General
- Topic: How to center the Grid
- Replies: 12
- Views: 19678
Re: How to center the Grid
Still waiting for your response
- Fri Mar 24, 2017 4:21 pm
- Forum: General
- Topic: How to center the Grid
- Replies: 12
- Views: 19678
Re: How to center the Grid
reify wrote:Hi,
Which projector are you using? The 1186, 1188 and Optoma have a vertical lens shift wheel above the zoom wheel.
For 42XY, the grid should be closer to the back of the quartz (but inside the boundaries obviously) and at 25XY the projection will be closer to the front.
Viviteck H-1185HD
- Thu Mar 23, 2017 7:55 pm
- Forum: General
- Topic: How to center the Grid
- Replies: 12
- Views: 19678
Re: How to center the Grid
M-Williams wrote:Is your projector properly mounted. Did you have the PDF instructions?
yes, I have the PDF instructions and followed all the instructions.