Print fails

This section is for specific instructions for daily operations of the Solus printer and for troubleshooting. User submitted tips, etc. should go in the "Tips and Tutorials" section.
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:
Re: Print fails

Postby mongerdesigns » Thu Oct 18, 2018 3:44 pm

That is an old intel graphics card. Or at least an old driver. We require intel 4000 or higher. Or else full rgb may not be supported.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
hasd81
Novice
Posts:23
Joined:Mon Dec 05, 2016 3:39 am

Re: Print fails

Postby hasd81 » Thu Oct 18, 2018 6:26 pm

mongerdesigns wrote:That is an old intel graphics card. Or at least an old driver. We require intel 4000 or higher. Or else full rgb may not be supported.



It is a 4000. I rolled back the driver and am able to see it the way it is in the manual. Except now it says “ This display dose not support any of the advanced settings “
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: Print fails

Postby mongerdesigns » Thu Oct 18, 2018 6:31 pm

Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
hasd81
Novice
Posts:23
Joined:Mon Dec 05, 2016 3:39 am

Re: Print fails

Postby hasd81 » Thu Oct 18, 2018 6:48 pm

mongerdesigns wrote:Try updating your driver. https://downloadcenter.intel.com/produc ... phics-4000



Still the same
Attachments
359F2BED-2E5C-4AD6-964E-085CA21E7F26.jpeg
hasd81
Novice
Posts:23
Joined:Mon Dec 05, 2016 3:39 am

Re: Print fails

Postby hasd81 » Thu Oct 18, 2018 7:06 pm

im Not using an HDMI if that matters?
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: Print fails

Postby mongerdesigns » Thu Oct 18, 2018 8:07 pm

You need to use HDMI to see the FULL RGB settings. Vga connection already gives you full rgb, but it's an analog signal. We recommend HDMI.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
hasd81
Novice
Posts:23
Joined:Mon Dec 05, 2016 3:39 am

Re: Print fails

Postby hasd81 » Fri Oct 19, 2018 3:36 am

image.jpg
Switched to HDMI and changed set settings and now this
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: Print fails

Postby mongerdesigns » Fri Oct 19, 2018 3:59 am

Could be old resin, or old bulb. Try increasing the exposure time by 0.5 seconds and run the print again.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
joeyalbano
Novice
Posts:50
Joined:Mon Apr 25, 2016 3:49 pm

Re: Print fails

Postby joeyalbano » Wed Dec 12, 2018 5:36 pm

Anybody having a problem with only 1 side of the platform printing properly and the other side printing bad? I'm able to set up on the left side of contour only. Any suggestions?
User avatar
Jewelermdt
Solus Master
Posts:809
Joined:Sun Jul 19, 2015 10:38 pm
Location:N.W. Florida
Contact:

Re: Print fails

Postby Jewelermdt » Wed Dec 12, 2018 5:51 pm

May need to check your platform alignment to the quarts table. Do the calibration for it.
Another thing could be film tension on that side.

Who is online

Users browsing this forum: No registered users and 7 guests