Print fails
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
That is an old intel graphics card. Or at least an old driver. We require intel 4000 or higher. Or else full rgb may not be supported.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Print fails
mongerdesigns wrote:That is an old intel graphics card. Or at least an old driver. We require intel 4000 or higher. Or else full rgb may not be supported.
It is a 4000. I rolled back the driver and am able to see it the way it is in the manual. Except now it says “ This display dose not support any of the advanced settings “
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Print fails
Try updating your driver. https://downloadcenter.intel.com/produc ... phics-4000
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Print fails
mongerdesigns wrote:Try updating your driver. https://downloadcenter.intel.com/produc ... phics-4000
Still the same
Re: Print fails
im Not using an HDMI if that matters?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Print fails
You need to use HDMI to see the FULL RGB settings. Vga connection already gives you full rgb, but it's an analog signal. We recommend HDMI.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Print fails
Switched to HDMI and changed set settings and now this
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Print fails
Could be old resin, or old bulb. Try increasing the exposure time by 0.5 seconds and run the print again.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Novice
- Posts:50
- Joined:Mon Apr 25, 2016 3:49 pm
Re: Print fails
Anybody having a problem with only 1 side of the platform printing properly and the other side printing bad? I'm able to set up on the left side of contour only. Any suggestions?
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Print fails
May need to check your platform alignment to the quarts table. Do the calibration for it.
Another thing could be film tension on that side.
Another thing could be film tension on that side.
Who is online
Users browsing this forum: No registered users and 11 guests