Please try this driver:
http://www.driverscape.com/download/usb-serial-ch340
Starting/Finishing/Pausing a print
Re: Starting/Finishing/Pausing a print
Thanks for the driver! It installs perfectly and shows the USB adapter on com8.
I'm still not getting any joy from this hex code though. Everything is lined up:
1. Driver installed
2. Plugged in to USB2 slot, not USB3 just in case.
3. Com port properly set in CW to 19200 baud.
4. Com port speed set to 19200 in control panel
Is there something special I need to enable in the Projector? Maybe there's an option to enable RS232 communication?
Should I dig around for an old school serial cable to see if that helps? For some reason the PC I'm using has a serial port.
I'm still not getting any joy from this hex code though. Everything is lined up:
1. Driver installed
2. Plugged in to USB2 slot, not USB3 just in case.
3. Com port properly set in CW to 19200 baud.
4. Com port speed set to 19200 in control panel
Is there something special I need to enable in the Projector? Maybe there's an option to enable RS232 communication?
Should I dig around for an old school serial cable to see if that helps? For some reason the PC I'm using has a serial port.
Re: Starting/Finishing/Pausing a print
I can't find the baud rate listed in the manual...where did you see that?
Re: Starting/Finishing/Pausing a print
I think according to the instructions to setup everything it needs to run at 19200.
I'll have to see if I can find that PDF again.
I'll have to see if I can find that PDF again.
Re: Starting/Finishing/Pausing a print
studioqubed wrote:Hi, I have the OptomaHD37 and having auto shutoff is really a must because I often need to print over night. You probably have this but here is the hex code;
Power ON
~XX00 0 7E 30 30 30 30 20 30 0D
Power OFF (0/2 for backward compatible)
~XX01 1 7E 30 30 30 31 20 31 0D
Thanks!
Craig
Hi,
Can you maybe post a screenshot of your hex code so I can copy it verbatim? Also what driver are you using with your USB-to-Serial cable? For the life of me I can't get the autoshutdown to work. Any advice??
Thanks!
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Starting/Finishing/Pausing a print
hx19035 wrote:studioqubed wrote:Hi, I have the OptomaHD37 and having auto shutoff is really a must because I often need to print over night. You probably have this but here is the hex code;
Power ON
~XX00 0 7E 30 30 30 30 20 30 0D
Power OFF (0/2 for backward compatible)
~XX01 1 7E 30 30 30 31 20 31 0D
Thanks!
Craig
Hi,
Can you maybe post a screenshot of your hex code so I can copy it verbatim? Also what driver are you using with your USB-to-Serial cable? For the life of me I can't get the autoshutdown to work. Any advice??
Thanks!
Solved! viewtopic.php?f=3&t=289&p=2136#p2136
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Who is online
Users browsing this forum: No registered users and 78 guests