Not a good start to the day... Solus has been working beautifully for the past month or so after switching to the MJ Wax cast resin. The detail and the confidence in each grow has been one less headache to worry about. Last night, one of my employees was waiting on a grow to finish and was pressed for time. The wax that was really needed was completed and he was waiting on some of the taller, less important waxes to complete. Well they decided to pause the grow, pull of what they needed and hit the road. Well, instead of hitting pause, stop, or any other button that would safely stop the process, they accidentally hit play. And you guessed it, down the table went with waxes attached. Get here this morning, they remove the vat and low and behold, a nice crack right down the middle.
My questions are:
Can I print around the crack if a position my waxes accordingly? (until I get a new one)
And how do I go about replacing the quartz? Is that something I can do here? or do I have to send whole machine in and wait forever?
Thanks in advance,
Blake
Broke my quartz
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Broke my quartz
Are you using cw? The pause won't work on it. If you stop the grow, you can't continue.
With Contour you can pause and resume prints.
I don't recommend using the printer with a cracked Quartz. Need to replace it. You have already contacted me, so I will email you soon with the instructions on how to get a new piece and replace it.
With Contour you can pause and resume prints.
I don't recommend using the printer with a cracked Quartz. Need to replace it. You have already contacted me, so I will email you soon with the instructions on how to get a new piece and replace it.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Broke my quartz
We are using CW. He wasn't planning on continuing, he was just going to scrap the other waxes and start them over due to time constraints on the other one.
Thanks for your help!
Thanks for your help!
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Broke my quartz
you'll be able to replace the quartz yourself. BTDT
-
- Posts:3
- Joined:Fri Jun 03, 2016 4:15 pm
Re: Broke my quartz
can I get a copy of those instructions as well? my Solus shipped with a piece of lint under the quartz and it's starting to work it's way into the build area.
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Broke my quartz
Just take the screws out of the black housing and pull from back to clear the box. You then have access to clean out the inside of printer.
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Broke my quartz
Jewelermdt wrote:Just take the screws out of the black housing and pull from back to clear the box. You then have access to clean out the inside of printer.
Totally agree . Marc
Re: Broke my quartz
You'll need to loosen the bottom plate first so the back plate can clear the ports and reset switch.
I just emailed you the instructions.
I just emailed you the instructions.
Who is online
Users browsing this forum: No registered users and 8 guests