If your InFocus video projector displays a slanted screen/output on initial bootup or when adjusting your grid for setup, you need to use the "Keystone" button on the remote control to correct.
From the manual(buried deep in the PDF):
"Use the KEYSTONE
buttons on the remote
control to correct
trapezoid image issues
(wider top or bottom). "
Trapezoid Image Issues on InFocus Projector
Last edited by jeweltool on Sun Jul 05, 2015 8:00 pm, edited 1 time in total.
Re: Trapezoid Image Issues on InFocus Projector
Can you please post some images of the slanted grid? You should not need to adjust the keystone and it should be on the default setting.
Re: Trapezoid Image Issues on InFocus Projector
Slanted screen went away after a few clicks on the Keystone buttons.
Did not have a chance for a photograph.
Must be a pretty common adjustment since it has its own section of buttons on the remote control and was not part of the onscreen popup menu.
Did not have a chance for a photograph.
Must be a pretty common adjustment since it has its own section of buttons on the remote control and was not part of the onscreen popup menu.
Re: Trapezoid Image Issues on InFocus Projector
I had to adjust mine -5, i read some resolution is lost with that adjustment. I tried to tilt the projector (back) but surprisingly did not help trapezoidal issue.
- toddmichael
- Novice
- Posts:77
- Joined:Sun Jul 05, 2015 4:33 am
- Location:Motor City, Mi
Re: Trapezoid Image Issues on InFocus Projector
Is this what you mean about a trapezoid shape being an issue?
In image 459 shows a 2 ism mm distortion from top to bottom, and am I supposed to be seeing the bolded lines at right and bottom, as seen on top and left? This image is with phone placed under the buildhead, to get as straight shot as possible.
Images are Slice view and 3d view showing printable area almost all the time, and out side random.
Thoughts?
In image 459 shows a 2 ism mm distortion from top to bottom, and am I supposed to be seeing the bolded lines at right and bottom, as seen on top and left? This image is with phone placed under the buildhead, to get as straight shot as possible.
Images are Slice view and 3d view showing printable area almost all the time, and out side random.
Thoughts?
- Attachments
-
- 20151219_050740.jpg (45.54KiB)Viewed 16562 times
-
- 20151219_050722.jpg (41.95KiB)Viewed 16562 times
-
- 20151219_045459.jpg (45.2KiB)Viewed 16562 times
Toddmichael
Firestorm Cad / Jeweler / Designer
Firestorm Cad / Jeweler / Designer
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Trapezoid Image Issues on InFocus Projector
Todd,
I'm positive your lens is not sitting straight. Please make sure it is. You shouldn't be getting that bowing on the side.
I'm positive your lens is not sitting straight. Please make sure it is. You shouldn't be getting that bowing on the side.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Trapezoid Image Issues on InFocus Projector
Oh. It would be so nice to have a better metal lens holder for Christmas.
Solus Version 1.1?
Solus Version 1.1?
Last edited by jeweltool on Sat Dec 19, 2015 5:11 pm, edited 1 time in total.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Trapezoid Image Issues on InFocus Projector
Maybe you can print one out using your Solus 1.0? Hehe
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Trapezoid Image Issues on InFocus Projector
67mm diameter? Hmmmm?
It might just need version 1.1 for that build.
Though I bet every Solus owner would want one!
It might just need version 1.1 for that build.
Though I bet every Solus owner would want one!
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Trapezoid Image Issues on InFocus Projector
What's the issue with the holder? If it's a little loose you can just put some tape around your lens barrel and it will sit on it snug.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Who is online
Users browsing this forum: No registered users and 8 guests