Printed great last night. Projector shut off as planned. Tried to print another model this am. Didn't turn off or restart Contour.
Set up model in Contour....when I selected Print Wizard
Got this message.
Printing failed. Detected 1 USB serial port, but no Solus DLP controller among them.
Checked all connections, power, restarted computer 3 times.
THEN got this error
Printing failed Access denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED))
Suggestions?
Just Bob
Error Messages
Re: Error Messages
Bob turn everything off and try it again.
Re: Error Messages
Archerm wrote:Bob turn everything off and try it again.
SO Mark, you got the inside scoop or something??? hahaha
I must have restarted 6 times!!
Maybe 7 is the charm!
AND when I was trying to login on the Solus computer to get the newest update for Contour ( I KEEP it off the internet on purpose...good ol' Windows updates and all) WINDOWS caught me and took over! About an hour update!!
ANYWAY...it went past the Error messages. Go figure.
What did you know???
Just Bob
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Error Messages
Make sure to check your Full Rgb settings after the windows update.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Error Messages
Will do!
I did a print just after it started working....came out GREAT!
I did a print just after it started working....came out GREAT!
Re: Error Messages
Well, it's doing it again.
Printed last night. NOT CONNECTED to internet. Projector shut off as planned
Print was great.
turned on projector
Tried to print another item
SAME ERROR messages. Restarted computer, still error messages.
Suggestions?
THANKS!
Just Bob
Printed last night. NOT CONNECTED to internet. Projector shut off as planned
Print was great.
turned on projector
Tried to print another item
SAME ERROR messages. Restarted computer, still error messages.
Suggestions?
THANKS!
Just Bob
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Error Messages
Sounds like a USB issue. Try changing the cable and the USB port.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Error Messages
I'll give it a go.
Stay tuned.
Stay tuned.
Re: Error Messages
Changed the usb port. Only have one cable for SOLUS DLP controller. ASSUMING that's the silver cable that shuts off the projector when finished/??
It's not recognizing the USB for the DLP controller
It's not recognizing the USB for the DLP controller
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Error Messages
No. That is the main usb cable.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Who is online
Users browsing this forum: No registered users and 8 guests