1.9.4v

dcpattni
Novice
Posts:97
Joined:Sat May 07, 2016 4:55 pm
Location:Dar-es-salaam,TANZANIA
Contact:
1.9.4v

Postby dcpattni » Tue Jan 16, 2018 9:08 pm

Hello Everyone,

After printing 6x4x2mm for scaling adjustment and wanted to print same again to see if scaling.... found area have changed i can't use full area.

plz help me asap.
Attachments
platform size change itself.JPG
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: 1.9.4v

Postby mongerdesigns » Wed Jan 17, 2018 1:22 am

Show us your Scale Adjustment screen.

You cannot use a 6x4x2mm to adjust the scaling. Obviously that would completely mess up the scaling.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: 1.9.4v

Postby mongerdesigns » Wed Jan 17, 2018 2:43 am

That means printing a 10x10x10 cube is giving you a 5x4x10 cube. Not possible.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: 1.9.4v

Postby mongerdesigns » Wed Jan 17, 2018 2:47 am

You need to first put all the numbers to 10. Then print a 10x10x10 cube. Then measure it and put the new numbers on the bottom row. Then the software will adjust the scaling based on that.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
dcpattni
Novice
Posts:97
Joined:Sat May 07, 2016 4:55 pm
Location:Dar-es-salaam,TANZANIA
Contact:

Re: 1.9.4v

Postby dcpattni » Wed Jan 17, 2018 3:40 am

first i did 10 10 10 all then i print 6x4x2 almost like in video but i did not change original scale that is why platform area small....after i enter 6 x 4 x 10 at original scale and actual scale 5.98x 4.02 x 10 platform correct.. now again i'm printing 6x4x2 to see as per video doing....is it right.
Attachments
correct.JPG
User avatar
Jewelermdt
Solus Master
Posts:809
Joined:Sun Jul 19, 2015 10:38 pm
Location:N.W. Florida
Contact:

Re: 1.9.4v

Postby Jewelermdt » Wed Jan 17, 2018 3:42 am

If you watch the video closely, you would have seen him change the top X an Y box measurements to 6 and 4 from 10 and 10.

But as Emil said it's best to print a 10 x 10 x 10 cube and use those measurements. READ your instruction manual.
Zalman
Novice
Posts:10
Joined:Sun Jul 02, 2017 12:20 pm
Contact:

Re: 1.9.4v

Postby Zalman » Wed Feb 14, 2018 9:50 am

Hi guys
please tell me how can I fix this distortion, I tried all the known variants?a cube in the corners does not work 10x10, maybe 2 out of four turns out 10x10, with the central cube no problems.
Attachments
BOX.jpg
User avatar
Jewelermdt
Solus Master
Posts:809
Joined:Sun Jul 19, 2015 10:38 pm
Location:N.W. Florida
Contact:

Re: 1.9.4v

Postby Jewelermdt » Thu Feb 15, 2018 2:45 am

I would not complain about .2 off in all corners. I believe you get this because of the curved lens is going to bend the light to some degree.
Zalman
Novice
Posts:10
Joined:Sun Jul 02, 2017 12:20 pm
Contact:

Re: 1.9.4v

Postby Zalman » Thu Feb 15, 2018 9:57 am

Jewelermdt wrote:I would not complain about .2 off in all corners. I believe you get this because of the curved lens is going to bend the light to some degree.


Thanks for answer.Can be replaced with a more accurate lens that comes with the printer?

Who is online

Users browsing this forum: No registered users and 9 guests