Page 32 of 42
Re: ***Totally Stoked!!***
Posted: Fri Jul 14, 2017 2:34 pm
by Archerm
A few castings from yesterday. All were emerald prints cast using Plasticast.
![Image](https://photos.smugmug.com/3d-printing/i-HTf7BtT/0/ca1759a1/L/20170714_102220-L.jpg)
Re: ***Totally Stoked!!***
Posted: Fri Jul 14, 2017 7:50 pm
by dcpattni
Hello Mark
Top class print & casting you get always.....i.m dont get same for rings it gets lines i need to fill up with super glue or wax to make levelling......if possbile can you share yr setting for 80x45- 25z or 20z....
DId try 2mm rod same height they comes out nice.
https://drive.google.com/file/d/0B0kqKa ... sp=sharing
Re: ***Totally Stoked!!***
Posted: Mon Jul 17, 2017 2:46 am
by Archerm
I will check monday.
Re: ***Totally Stoked!!***
Posted: Mon Jul 17, 2017 6:39 pm
by rkundla
mongerdesigns wrote:I don't think that's overcure. His build tables are probably calibrated a little too close. So it's compression of the first few layers.
Ahh, I didn't think of that.
![Razz :-P](./images/smilies/icon_razz.gif)
Re: ***Totally Stoked!!***
Posted: Mon Jul 17, 2017 7:39 pm
by Archerm
dcpattni wrote:Hello Mark
Top class print & casting you get always.....i.m dont get same for rings it gets lines i need to fill up with super glue or wax to make levelling......if possbile can you share yr setting for 80x45- 25z or 20z....
DId try 2mm rod same height they comes out nice.
https://drive.google.com/file/d/0B0kqKa ... sp=sharing
![Image](https://photos.smugmug.com/3d-printing/i-9hhKm4H/0/3e140852/L/20170717_153546-L.jpg)
Re: ***Totally Stoked!!***
Posted: Fri Jul 21, 2017 6:16 pm
by M-Williams
Thank you for sharing.
Re: ***Totally Stoked!!***
Posted: Wed Jul 26, 2017 2:44 pm
by Archerm
I have a few two tone helicoil rings to finish up for next week. This will be the white gold helicoil insert. there will be a yellow gold cap on each end of the helicoil. Designed with a constant .5mm overall wall thickness and so the only support needed is the .5 mm fin support around the bottom.
![Image](https://photos.smugmug.com/3d-printing/i-gZw6X7W/0/eecd4d62/L/20170726_102514_001-L.jpg)
![Image](https://photos.smugmug.com/3d-printing/i-QMWxxqh/0/6ff4d273/L/20170726_103706-L.jpg)
Re: ***Totally Stoked!!***
Posted: Wed Aug 02, 2017 8:12 pm
by Archerm
Re: ***Totally Stoked!!***
Posted: Sun Aug 06, 2017 8:04 pm
by Dstonic
Mark, Absolutely outstanding !!!!
What resolution do you normally use , 48x27 or 80x45 ? Reason I ask, a few post back you showed your settings for 80x45.......I've had a issue growing a 12 mm wide ring size 13+ and it took up the whole scene. Should I have switched to 80x45? Thanks...>David
Re: ***Totally Stoked!!***
Posted: Mon Aug 07, 2017 2:04 am
by Jewelermdt
Hey David
He has 2 printers. One set up for each size.
If you have room all around the ring, it should print fine. Just use a lot of supports. Even half way up on side of ring to keep it from sagging mid print.