***Totally Stoked!!***

Show off your prints.
samatheang
Solus Expert
Posts:197
Joined:Wed Feb 17, 2016 10:36 pm
Re: ***Totally Stoked!!***

Postby samatheang » Mon Apr 17, 2017 6:54 pm

Thank you, Mark.

Archerm wrote:Here you go.

Image
samatheang wrote:Very nice and smooth print, Mark. Good job!

If you don't mind, could you share us screenshots of your profile settings for both 25xy and 41xy please? Thank you.
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Tue Apr 18, 2017 1:01 am

You know interesting that you said that.
I was thinking about printing a egg with a chicken inside!! :mrgreen:
mongerdesigns wrote:Where are the egg prints?
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Mon May 01, 2017 5:43 pm

It has been a little while since I posted any prints. It has been busy but wanted to take a few minutes to post a few. Bits and pieces along with a few bands.

Image

Image

Image

Image

Image

Image

Image

Image

Image
GSJ_NZ
Novice
Posts:33
Joined:Tue Oct 13, 2015 4:15 am

Re: ***Totally Stoked!!***

Postby GSJ_NZ » Mon May 01, 2017 9:58 pm

As always, great prints, and thanks very much for sharing them!
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Mon Jun 05, 2017 9:23 pm

Still around but have been busy!! A few prints for you!! Nothing fancy just paying the bills!! :ugeek: :ugeek:

Image

Image

Image

Image

Image
User avatar
M-Williams
Solus Master
Posts:393
Joined:Sun Nov 01, 2015 4:45 pm

Re: ***Totally Stoked!!***

Postby M-Williams » Mon Jun 05, 2017 10:40 pm

Beautiful prints. I'm really impressed my the beaded edge bands.
Dstonic
Novice
Posts:54
Joined:Thu Mar 09, 2017 1:52 pm
Location:Breaux Bridge, Louisiana

Re: ***Totally Stoked!!***

Postby Dstonic » Tue Jun 06, 2017 12:50 pm

....and the star shaped cutters use for the stones. Noticed that right off looking down the holes. Nice touch there Mark!
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Tue Jun 06, 2017 3:25 pm

Thanks everyone!! Just doing a few easy prints this week. Most are remakes of customers jewelry that is just worn out. Sometimes it is just easier to remake than repair. :mrgreen:

Image

Image

Image
User avatar
Eoin Rogan
Novice
Posts:23
Joined:Thu May 05, 2016 11:23 am

Re: ***Totally Stoked!!***

Postby Eoin Rogan » Wed Jun 07, 2017 10:16 am

Amazing!
samatheang
Solus Expert
Posts:197
Joined:Wed Feb 17, 2016 10:36 pm

Re: ***Totally Stoked!!***

Postby samatheang » Wed Jun 07, 2017 6:09 pm

The prints looks amazing! I use that support style for printing horizontally too. It works very well. Thank to you, Mark. :)

Archerm wrote:Thanks everyone!! Just doing a few easy prints this week. Most are remakes of customers jewelry that is just worn out. Sometimes it is just easier to remake than repair. :mrgreen:

Image

Image

Image

Who is online

Users browsing this forum: No registered users and 6 guests