I did some tests with the Solus and must say the quality is very good.
I was working on a ring and decided to have a test with this piece, design was not yet finished and I wanted to have a real life preview.
Printing time 2H30 compare to 9 hours with my micro...not bad.
Surface resolution is very nice, attached is a Matrix picture of the final piece as well.
Prints by Tiger
Re: Prints by Tiger
Knap André
Now in English, very nice!
Surface quality, sharp! Better than micro?
Now in English, very nice!
Surface quality, sharp! Better than micro?
Re: Prints by Tiger
Better than micro, 25microns in plaats van 35microns.
No steps visible, very smooth finish
No steps visible, very smooth finish
Re: Prints by Tiger
Very good test. I am ordering my second Solus Monday to set up for 42xy. That way I wont have to switch back and forth on the one I already have.
Re: Prints by Tiger
The only way to compare quality is to print the same file on different printers.
Here is a test I did, comparing the Envisiontec Micro wit the Solus.
Same file sent to the same company, cast on the same tree.
Printed on the Solus with B9R-3-Emerald, printed on the Micro with EC500M.
The wax is smoother on the Solus, no growing lines, you can definitely see the difference on the pictures (first one Solus on the right, second one Solus on the left).
Definition is slightly sharper on the Solus.
Casting with the Emerald resin is very good, I wasn't so lucky with the sherry one (I didn't cast myself).
Printing time is 3 time faster as well, not bad if you are in a hurry
Here is a test I did, comparing the Envisiontec Micro wit the Solus.
Same file sent to the same company, cast on the same tree.
Printed on the Solus with B9R-3-Emerald, printed on the Micro with EC500M.
The wax is smoother on the Solus, no growing lines, you can definitely see the difference on the pictures (first one Solus on the right, second one Solus on the left).
Definition is slightly sharper on the Solus.
Casting with the Emerald resin is very good, I wasn't so lucky with the sherry one (I didn't cast myself).
Printing time is 3 time faster as well, not bad if you are in a hurry
Re: Prints by Tiger
So our friend can cast the Emerald resin! Good to know.
Thanks for the info Tiger and showing us the difference.
Solus, better print quality, faster and way cheaper than the Micro...
Thanks for the info Tiger and showing us the difference.
Solus, better print quality, faster and way cheaper than the Micro...
Re: Prints by Tiger
I am running some test prints with the green right now. I like your test results. They coincide with the results I have been getting.
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Prints by Tiger
This is Mind blowing quality . Very nice prints.
Tiger. Do you cure your Emerald resin ?
Tiger. Do you cure your Emerald resin ?
Re: Prints by Tiger
Yes, resin is cured 6 min in a Photopol curing unit.
I clean the piece 15sec in propanol, dry with compressed air, 30 min at 38°C, 6 min in Photopol.
I just bought a microwave and will try curing with baby oil as well.
I clean the piece 15sec in propanol, dry with compressed air, 30 min at 38°C, 6 min in Photopol.
I just bought a microwave and will try curing with baby oil as well.
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Prints by Tiger
Tiger. Thank you for your valuable tips. Your prints are really nice .looking forward to see more of your great work. Thank you for sharing.
Who is online
Users browsing this forum: No registered users and 102 guests