I have been waiting for the go ahead with this project and finally got it last Friday.It will be Tanzanite and Diamond. It also just so happens the second Solus for the shop came in last week as well. I spent some time setting up the Solus for 42xy for larger projects. It will be nice to have 2 printers so I don't have to change one back and forth. This pendent is 45mm X 35mm. This was the first print on the new Printer. Stoked again!!
The Twins!!
Largest project print to date!!
Last edited by Archerm on Mon Feb 15, 2016 10:47 pm, edited 1 time in total.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Largest project print to date!!
Ha! That looks incredible, Mark!
First print on your second Solus. Wow.
First print on your second Solus. Wow.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Largest project print to date!!
Thanks Emil,
It was kind of hard to orient the piece not to get build lines. The sides angle down and away from the two center stones so any way I angled it I would get them. The piece is pretty smooth. It wont take much to clean up the castings. Mark
It was kind of hard to orient the piece not to get build lines. The sides angle down and away from the two center stones so any way I angled it I would get them. The piece is pretty smooth. It wont take much to clean up the castings. Mark
Re: Largest project print to date!!
I am trying to decide what to do about the computers? I am just using the one lap top now and cant decide whether to get another laptop or a pc that will run both. Laptops are cheap.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Largest project print to date!!
Archerm wrote:Thanks Emil,
It was kind of hard to orient the piece not to get build lines. The sides angle down and away from the two center stones so any way I angled it I would get them. The piece is pretty smooth. It wont take much to clean up the castings. Mark
Have you tried slicing at 25 micron Z? Or even 20 microns? I'm sure it will take away any build lines you might get, but will add some time to the print.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Largest project print to date!!
No since it was my first print at 42xy. Is the profile the same except for the slice thickness?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Largest project print to date!!
You can try with the same profile. Just change the slice thickness value. If you get overcuring, which you shouldn't, then lower the layer exposure a bit.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Largest project print to date!!
Looks great Mark. How much longer did the print take?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Largest project print to date!!
It took about 38 minute longer. But will save alot more than that in cleanup. Have you ever tried .01??
Who is online
Users browsing this forum: No registered users and 110 guests