Ben's Prints
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
They have a suggested burnout schedule on their site. I haven't casted it myself. Might want to contact Shane from Makerjuice.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Ben's Prints
Tried casting with the MJ Waxcast resin and had pretty bad results. We used the recommended burnout schedule that was on their site. Cured the model in a UV box on and off for 8-12 hours and it seemed to be fully cured.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Ben's Prints
I would contact Shane Graber from MakerJuice.
memberlist.php?mode=viewprofile&u=460
I've been hearing a lot of the same from other customers. Thinner pieces cast ok with WaxCast, but thicker pieces don't turn out too well. This is following their recommended burnout.
memberlist.php?mode=viewprofile&u=460
I've been hearing a lot of the same from other customers. Thinner pieces cast ok with WaxCast, but thicker pieces don't turn out too well. This is following their recommended burnout.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Ben's Prints
While my surface finish wasn't as bad as your casting, I had more voids in my casting than normal. I probably need to run the high temp phase longer or be extra vigilant about getting ash out of the flask.
Shane mentioned previously that there were water-soluble additives that would help with casting, but I can't say that I've seen the benefit just yet. Maybe I needed to run my Plasticast at the 36:100 water ratio. I found even 38:100 to be really thick and started to thicken too quickly for my tastes.
Shane mentioned previously that there were water-soluble additives that would help with casting, but I can't say that I've seen the benefit just yet. Maybe I needed to run my Plasticast at the 36:100 water ratio. I found even 38:100 to be really thick and started to thicken too quickly for my tastes.
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Ben's Prints
Messerbr wrote:Tried casting with the MJ Waxcast resin and had pretty bad results. We used the recommended burnout schedule that was on their site. Cured the model in a UV box on and off for 8-12 hours and it seemed to be fully cured.
Any chance with your castings .Did you use plasticast on that one.
Re: Ben's Prints
Unimpressed with MakerJuice! They send me an open bottle and haven't gotten back to me about it yet!
Resin all over the inside of the package.
Resin all over the inside of the package.
Re: Ben's Prints
some prints and castings as well as a video link to my Kitten ring 2.0 https://youtu.be/PXwnyl-jdHQ
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Ben's Prints
Nice!
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Novice
- Posts:96
- Joined:Mon Mar 28, 2016 8:05 am
Re: Ben's Prints
Nice casting
Re: Ben's Prints
Having an interesting type of failure here... It looked like the print came out alright but when I went touched it it wasnt all solid. Has anyone had something like this happen to them?
Who is online
Users browsing this forum: No registered users and 46 guests