Fleur De Lis Ring test print. This ring was only meant to be printed on a solidscape. No more.
Prints by Monger
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Prints by Monger
Solus Rocks. Please how do you clean your prints. do you use alcohol.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Prints by Monger
Yes. I use alcohol. 91%.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Prints by Monger
Do you soak and swirl or do you use an ultrasonic? I'd think the ultrasonic would help get the uncured resin out from all that detail.
That ring looks fantastic. Nice to see that you can print it without the dissolvable support wax. Did you UV cure that as well?
That ring looks fantastic. Nice to see that you can print it without the dissolvable support wax. Did you UV cure that as well?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Prints by Monger
rkundla wrote:Do you soak and swirl or do you use an ultrasonic? I'd think the ultrasonic would help get the uncured resin out from all that detail.
That ring looks fantastic. Nice to see that you can print it without the dissolvable support wax. Did you UV cure that as well?
Thanks Ron. I have a large plastic container full of "dirty" ipa that I agitate the part in for a minute. Then I use a plastic squeeze bottle with clean ipa to wash the part again. (the ipa then goes back into the bottle, and eventually if it gets dirty enough, goes into the "dirty" container, and the bottle gets refilled with brand new ipa).
I have tried the ultrasonic and it works well, but in most cases it's not necessary.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Prints by Monger
mongerdesigns wrote:https://www.youtube.com/watch?v=ZIadbssZqN0
hi There, here asking.
how much size of top-Radius/Length of Supports?
They look very thin.
I'm worried about that are TOPs printable?
----
STRANGE FREAK DESIGNS JAPAN
Naoto Furuya
http://www.stfreak.com
sfd-info@stfreak.com
----
Zbrush since 2015 September
solus since 2016 March
----
STRANGE FREAK DESIGNS JAPAN
Naoto Furuya
http://www.stfreak.com
sfd-info@stfreak.com
----
Zbrush since 2015 September
solus since 2016 March
----
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Prints by Monger
NF.JP wrote:mongerdesigns wrote:
hi There, here asking.
how much size of top-Radius/Length of Supports?
They look very thin.
I'm worried about that are TOPs printable?
The thinnest parts are 0.2mm in diameter.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Prints by Monger
Testing a new prototyping orange resin.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Prints by Monger
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Prints by Monger
Looks fabulous .Is This the solus new Resin.
Who is online
Users browsing this forum: No registered users and 8 guests