failures in printing with resin solus art

Discuss 3d printing resins
mexport2018
Posts:8
Joined:Fri Oct 12, 2018 4:10 pm
failures in printing with resin solus art

Postby mexport2018 » Wed Dec 05, 2018 8:38 pm

good afternoon, please someone to help me in how to set the profile change to use another resin, just change the profile on the Solus Contour or also you have to configure the projector ???? because today I did a test with Solus art resin and only printed the base of the supports and the rest was stuck in the film. Some suggestions please.
Normally my printer works with the resin Solus proto and I have no problem, but I want to make tests with Solus art resin and they fail even though the profile changes.
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: failures in printing with resin solus art

Postby mongerdesigns » Wed Dec 05, 2018 9:03 pm

Open Contour, then go to EDIT, PRINT PROFILE.

Then you will see a drop down box on the top left that says "Resin Profile".

You can select the correct resin profile there and press OK.

For the ArtGrey resin you need to use thicker support tips on the bottom of the prints. At least 0.4-0.6mm tips. To make sure it holds the part well.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
mexport2018
Posts:8
Joined:Fri Oct 12, 2018 4:10 pm

Re: failures in printing with resin solus art

Postby mexport2018 » Wed Dec 05, 2018 10:24 pm

thank you very much for the data, and for resin wax cast what kind of supports should I put ??? because I also have the same problem with resin wax cast .....
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: failures in printing with resin solus art

Postby mongerdesigns » Wed Dec 05, 2018 10:42 pm

Again, thicker ones. 0.6 is recommended.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
mexport2018
Posts:8
Joined:Fri Oct 12, 2018 4:10 pm

Re: failures in printing with resin solus art

Postby mexport2018 » Wed Dec 05, 2018 10:53 pm

I did a first test with the solus art resin and only printed the base nothing else, and I noticed the projector and I see that it does not shoot the light towards the printer, but the platform moves normally as if it were printing, what would be the problem? ??
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: failures in printing with resin solus art

Postby mongerdesigns » Wed Dec 05, 2018 11:22 pm

Run a print without the resin tank and without the build plate and make a video if you can for the first min or so. Then email it to me at info@junction3d.com
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
mexport2018
Posts:8
Joined:Fri Oct 12, 2018 4:10 pm

Re: failures in printing with resin solus art

Postby mexport2018 » Thu Dec 06, 2018 4:04 pm

f I already sent the video you asked me to your email. Thank you
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: failures in printing with resin solus art

Postby mongerdesigns » Thu Dec 06, 2018 5:25 pm

Yes, I saw it. Everything is working as it should. After the initial layers are done, the white light turns blue. If you want white light all the time, move the Intensity slider all the way to the Right (to 8), in the resin profile window.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
khoover
Posts:5
Joined:Mon Dec 21, 2015 10:55 pm

Re: failures in printing with resin solus art

Postby khoover » Thu Dec 06, 2018 5:48 pm

Just purchased some SolusArt Grey resin to test but profile does not appear in the Contour software when I look there. I also purchased a test bottle of SolusCast 1.0 and that profile does appear in Contour. What gives? Where can I get the profile for SolusArt Grey ?
mexport2018
Posts:8
Joined:Fri Oct 12, 2018 4:10 pm

Re: failures in printing with resin solus art

Postby mexport2018 » Thu Dec 06, 2018 5:52 pm

You need to enable beta from Edit, Preferences and then check for updates again under HELP.

Who is online

Users browsing this forum: No registered users and 18 guests