Hi guys,
Can anybody tell me why my prints are coming out skewed? for example the coin I made are coming out oval not round, see picture please. If anybody can help, it'll be great. Thanks guys.
EasyCast HD Print problems
-
- Novice
- Posts:50
- Joined:Mon Apr 25, 2016 3:49 pm
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: EasyCast HD Print problems
Check and make sure your grid had the correct aspect ratio.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Novice
- Posts:50
- Joined:Mon Apr 25, 2016 3:49 pm
Re: EasyCast HD Print problems
Hi Monger,
I just used the default settings, should I modify it? Attached is the grid that I'm using.
I just used the default settings, should I modify it? Attached is the grid that I'm using.
-
- Novice
- Posts:50
- Joined:Mon Apr 25, 2016 3:49 pm
Re: EasyCast HD Print problems
Hi Guys,
Any suggestions?
Any suggestions?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: EasyCast HD Print problems
You gotta measure it on the glass (projecting it on a paper). Make sure the width and length are correct.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: EasyCast HD Print problems
Hello everyone! What can cause this problem of print.
Some prints coming ok but some they are like cut .
After printing I have in tank some uncured big pieces of resins.
Some prints coming ok but some they are like cut .
After printing I have in tank some uncured big pieces of resins.
Re: EasyCast HD Print problems
I have a question and is not the problem with the bulb is new projector..100 hours used. anyone can help?
print with 25nm x 30nm
i spoted the marks on the pictures. looks like mess
how can i have clean prints ?
is maybe contrast and brightness on the nvidia settings ??
print with 25nm x 30nm
i spoted the marks on the pictures. looks like mess
how can i have clean prints ?
is maybe contrast and brightness on the nvidia settings ??
Re: EasyCast HD Print problems
Filter the resin before and after use. Also try maybe a slightly lower exposure time for the base layers. They appear to have some bleeding.
Check your model if it is 100% watertight. And look in the slicer if you see weird spots on the places that have the resin dirt.
I just looked again. Maybe it is dirty alcohol or whatever you use to clean the models. Or not cleaning them well enough. Then the dirt can stick to the model and when post-curing it will bake to the model. I have had that on some occasions.
Check your model if it is 100% watertight. And look in the slicer if you see weird spots on the places that have the resin dirt.
I just looked again. Maybe it is dirty alcohol or whatever you use to clean the models. Or not cleaning them well enough. Then the dirt can stick to the model and when post-curing it will bake to the model. I have had that on some occasions.
Re: EasyCast HD Print problems
thanks.
Who is online
Users browsing this forum: No registered users and 16 guests