No. We haven't tried them. It was just released 2 days ago. We were not one of the "privileged" ones to receive early sample bottles from b9 creations, for obvious reasons, although I'm sure we sell a lot of resin for them
If anyone wants to try it, it should work just fine. I'm thinking the exposure would be lowered a bit. If it's 25% faster than the b9 cherry, like mentioned by Mike, then on the 25xy30z you should start at 2100ms for the layer exposure. The base exposure doesn't matter as much but you can lower it a bit from 23000 down to 20000. With a little trial and error you can dial it in, until we get our hands on it and make some tested resin profiles.
One quality higher than B9 Cherry?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: One quality higher than B9 Cherry?
mongerdesigns wrote:No. We haven't tried them. It was just released 2 days ago. We were not one of the "privileged" ones to receive early sample bottles from b9 creations, for obvious reasons, although I'm sure we sell a lot of resin for them
If anyone wants to try it, it should work just fine. I'm thinking the exposure would be lowered a bit. If it's 25% faster than the b9 cherry, like mentioned by Mike, then on the 25xy30z you should start at 2100ms for the layer exposure. The base exposure doesn't matter as much but you can lower it a bit from 23000 down to 20000. With a little trial and error you can dial it in, until we get our hands on it and make some tested resin profiles.
Thanks .. Im sure you will sell a lot of resin for them ... after the solus I don't think Id ever want to go back to a B9C ...
Does your upcoming Solus Resin also claim to be Ash Free like they're yellow Resin?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: One quality higher than B9 Cherry?
So far so good from the tests we've done.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: One quality higher than B9 Cherry?
mongerdesigns wrote:So far so good from the tests we've done.
Can I get a test print to cast? prob will try both your new resin and theirs and see which works best for me
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: One quality higher than B9 Cherry?
Do you have a RUFF guess when the Solus resin will be released??
I'm getting close to needing more.
Thanks
Mike
I'm getting close to needing more.
Thanks
Mike
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: One quality higher than B9 Cherry?
I'm Too a volunteer to Beta test The new resin .
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: One quality higher than B9 Cherry?
A rough guess would be beginning of January or maybe sooner. But again, can't be sure with these things.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: One quality higher than B9 Cherry?
Jewelermdt wrote:Do you have a RUFF guess when the Solus resin will be released??
I'm getting close to needing more.
Thanks
Mike
If you need resin you should get more cherry. You shouldn't wait for this resin, because we are still testing.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: One quality higher than B9 Cherry?
Ok Will do.
Re: One quality higher than B9 Cherry?
So while I wait for your new Resin I decided to order and try B9's Yellow Resin which the claim is ash free and will cast better in my situation.
Would rather not use my B9C if I can avoid it so ... would you have a suggestion for a base point in what I should change in settings ... other than exposure time which I guess will just be a proportional change? same ratio as a B9Creator to Solus for Cherry applied to their yellow profile?
Thanks!
Would rather not use my B9C if I can avoid it so ... would you have a suggestion for a base point in what I should change in settings ... other than exposure time which I guess will just be a proportional change? same ratio as a B9Creator to Solus for Cherry applied to their yellow profile?
Thanks!
Who is online
Users browsing this forum: No registered users and 154 guests