SolusCast: Success Print and Cast

Discuss casting techniques
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm
SolusCast: Success Print and Cast

Postby M.A.N » Sat Sep 23, 2017 11:31 am

Hi everyone.
These pics are my first prints and casts with soluscast.
As in previous post about soluscast there were lots of suggestions in curing and casting and lots of fails i decided to make new one.
PRINTING
1-These 4 ring model were printed in 2:45 hours.
2-Cleaned with alcohol then rinsed in clean alcohol and stayed there about 10 mins.
3-They cured in 2 different times. Both in plastic bottle full of water. My cure unit is a nail dryer with 4، 8 watts lamps and i added two more at its bottom.
Two models in right side were cured in 6 houres. It was long time so it causes them to crash in some places.
Two in the left were cured in 2 hours. It was enough and they were fine. As you see one of them is a heavy ring.
Water temperature reaches about 60 degrees.
CASTING
1-As i notice The most important thing about this resin is your INVESTMENT.
I suggest you to buy G3D SYNERGY.
2- mix it 38:100
3- leave it 3 hours
4- put it in oven. This was my oven program :
Ramp to 250 c in one hour and stay for another one hour
Ramp to 400 c in one hour and stay 2 hours
Ramp to 800 c in one hour and stay 3 hours
Return to 700 c and stay another 2 hours.
Then i vaccumed inside flask about 0.4 bar(important).
Return back to oven for another 1 hour.
I cast it in 700 c.
And these are the result.
Attachments
DSC_0473.JPG
Cast tree after magni polish
DSC_0463.JPG
Casted tree
_20170922_212030.JPG
Tree
_20170922_211850.JPG
Printed rings
DSC_0445.JPG
Print
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm

Re: SolusCast: Success Print and Cast

Postby M.A.N » Sat Sep 23, 2017 11:36 am

Cuted Rings
Attachments
DSC_0477.JPG
Cuted Rings
A.Joa1
Novice
Posts:54
Joined:Sat Dec 03, 2016 11:43 am

Re: SolusCast: Success Print and Cast

Postby A.Joa1 » Sat Sep 23, 2017 11:52 am

Very very nice!

An excellent example of design, print and casting.

I really like your designs. Great work!

Thanks for sharing.
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm

Re: SolusCast: Success Print and Cast

Postby M.A.N » Sat Sep 23, 2017 11:55 am

Thank you
Jules
Novice
Posts:22
Joined:Sat Feb 20, 2016 2:05 am

Re: SolusCast: Success Print and Cast

Postby Jules » Sat Sep 23, 2017 2:34 pm

Excellent !

Are you vacuum casting or centrifugal?

Looks like they don't sell that investment in the states, where are you buying it at?
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm

Re: SolusCast: Success Print and Cast

Postby M.A.N » Sat Sep 23, 2017 3:00 pm

I use vacuum casting.
Its a british investment. It shwbe available in us.
I used to use prestige optima for my b9 models. I think that should work too. But synergy investment quality is much better.
Attachments
EU-G3D-SYNERGY-Datasheet-Nov18-2016.pdf
Synergy pdf
(803.77KiB)Downloaded 637 times
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: SolusCast: Success Print and Cast

Postby mongerdesigns » Sat Sep 23, 2017 3:28 pm

Amazing prints and casts! Thank you for posting your results. :)
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
User avatar
rkundla
Solus Master
Posts:308
Joined:Sat Jan 09, 2016 6:01 am

Re: SolusCast: Success Print and Cast

Postby rkundla » Sat Sep 23, 2017 9:32 pm

What type of kiln/oven/furnace are you using to burn out the prints?

You mention that vacuuming out at 0.4 bar as being important. How did you go about doing this? With a vacuum chamber or an actual vacuum? How did you measure the pressure?
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm

Re: SolusCast: Success Print and Cast

Postby M.A.N » Sun Sep 24, 2017 1:56 am

rkundla wrote:What type of kiln/oven/furnace are you using to burn out the prints?

You mention that vacuuming out at 0.4 bar as being important. How did you go about doing this? With a vacuum chamber or an actual vacuum? How did you measure the pressure?


I use an electric kiln. It can reach 850 c degrees.
I vacuum all of my resin models. As you can see my casted tree was all resins. Vacuuming flask for resin models makes sure you will have no ashes or unburned resin and so a better cast. Then you have to return it to oven for at least one hour.
I vaccum my flask with my vacuum casting machine. I simply put my flask upside down on its vaccum chamber
And turn its vaccum motor on and it has barometer. When it reaches -0.4 i turn it off.
User avatar
rkundla
Solus Master
Posts:308
Joined:Sat Jan 09, 2016 6:01 am

Re: SolusCast: Success Print and Cast

Postby rkundla » Sun Sep 24, 2017 2:40 am

M.A.N wrote:I use an electric kiln. It can reach 850 c degrees.

Do you have additional air holes or vents in your kiln to improve combustion? What is your ramp rate when moving between the temperature stages?

M.A.N wrote:I vacuum all of my resin models. As you can see my casted tree was all resins. Vacuuming flask for resin models makes sure you will have no ashes or unburned resin and so a better cast. Then you have to return it to oven for at least one hour.
I vaccum my flask with my vacuum casting machine. I simply put my flask upside down on its vaccum chamber
And turn its vaccum motor on and it has barometer. When it reaches -0.4 i turn it off.

I see. Do you know if you see any debris in the machine after you do that? That is a very interesting way of dealing with the ash.

Who is online

Users browsing this forum: No registered users and 4 guests