solus wax burnout

Discuss casting techniques
kostyo
Novice
Posts:41
Joined:Thu Apr 27, 2017 2:14 pm
solus wax burnout

Postby kostyo » Tue Jul 17, 2018 4:32 pm

Hi All

tomorrow I will be 100ml solus wax for the test ... I hope it will to print on the LCD printer.

what is the best burnot process for plasticast?

now I'm using epic M and burnout process 2h 150celzius ramp up at 2h 720 celsius and 1h on 480c and casting ... can i use it on solus wax?

Thanks
User avatar
Messerbr
Solus Expert
Posts:163
Joined:Tue Jan 05, 2016 2:54 pm
Location:North Carolina
Contact:

Re: solus wax burnout

Postby Messerbr » Tue Jul 17, 2018 6:11 pm

http://www.reify-3d.com/forum/viewtopic.php?f=8&t=1180

Ramping straight to 1450 and holding for 3 or 4 hours then drop to casting temperature seems to work well.
artcad
Novice
Posts:73
Joined:Sun Aug 07, 2016 11:37 pm

Re: solus wax burnout

Postby artcad » Tue Sep 25, 2018 10:32 pm

1450 fahrenheit is 787 celsius right?So this works well?
User avatar
Ted Broadside
Novice
Posts:40
Joined:Mon Jun 27, 2016 8:38 am
Location:Bedford UK

Re: solus wax burnout

Postby Ted Broadside » Fri Mar 15, 2019 9:28 am

Messerbr,

Can you tell me when you put the flask into the kiln when ramping up to 1450? as soon as the kiln is turned on or when it reaches that temperature?
User avatar
Messerbr
Solus Expert
Posts:163
Joined:Tue Jan 05, 2016 2:54 pm
Location:North Carolina
Contact:

Re: solus wax burnout

Postby Messerbr » Fri Mar 15, 2019 1:31 pm

Ted Broadside wrote:Messerbr,

Can you tell me when you put the flask into the kiln when ramping up to 1450? as soon as the kiln is turned on or when it reaches that temperature?


I put the flask into a cold kiln so it would be in there while temperatures went from 70F to 1450F. Although, we have switched back to using the b9 emerald resin due to shrinkage and printing problems we had with the SolusWax. I would also recommend trying a sample bottle of the Resinworks EasyCast.
User avatar
Ted Broadside
Novice
Posts:40
Joined:Mon Jun 27, 2016 8:38 am
Location:Bedford UK

Re: solus wax burnout

Postby Ted Broadside » Fri Mar 15, 2019 1:43 pm

I've just ordered myself a sample bottle, thanks. Don't you get ash left in the flask using the emerald resin? I used to use that and I would constantly get pitted castings from (I presume) ash left in the flask, that's why I tried the Soluswax, but I'm still having a few problems with that.
User avatar
Messerbr
Solus Expert
Posts:163
Joined:Tue Jan 05, 2016 2:54 pm
Location:North Carolina
Contact:

Re: solus wax burnout

Postby Messerbr » Fri Mar 15, 2019 5:17 pm

Ted Broadside wrote:I've just ordered myself a sample bottle, thanks. Don't you get ash left in the flask using the emerald resin? I used to use that and I would constantly get pitted castings from (I presume) ash left in the flask, that's why I tried the Soluswax, but I'm still having a few problems with that.


With the b9 green you just have to cure it a lot and then it casts pretty well. The process we've been using has been to:
- put prints in distilled water and microwave for 3 minutes, rest 15min, and repeat 3-4 more times
- UV cure 405nm light in distilled water in a clear container
- Invest with Plasticast 38:100 adding 1% of the powder weight of boric acid to distilled water
- Set for ~1 hour
- place flasks in oven on a 7 hour delay
- Burnout:
- Ramp 40F/min to 1000F hold 3 hr
- Ramp 40F/min to 1400F hold 5 hr
- Drop to casting temp and hold for an hour
- Vacuum flask with shop vac
- Put flask back in oven for 30min to 1 hour
- Cast

There are definitely still things that can be tweaked but the main thing with the emerald is microwaving and a long UV cure. The EasyCast resin seems to print a little better than the emerald and reaches a full cure in UV a little quicker
robin
Solus Expert
Posts:144
Joined:Wed Sep 23, 2015 3:03 pm

Re: solus wax burnout

Postby robin » Sat Mar 16, 2019 1:42 pm

Messerbr wrote:The EasyCast resin seems to print a little better than the emerald and reaches a full cure in UV a little quicker


Are you microwaving it as well as UV curing it?
User avatar
Messerbr
Solus Expert
Posts:163
Joined:Tue Jan 05, 2016 2:54 pm
Location:North Carolina
Contact:

Re: solus wax burnout

Postby Messerbr » Mon Mar 18, 2019 1:49 pm

robin wrote:
Messerbr wrote:The EasyCast resin seems to print a little better than the emerald and reaches a full cure in UV a little quicker


Are you microwaving it as well as UV curing it?


Just UV curing in distilled water for 2-3 hours and it seems to cast just as well as a fully cured emerald model
Juar75
Posts:8
Joined:Sat Jan 26, 2019 7:46 pm

Re: solus wax burnout

Postby Juar75 » Fri Sep 11, 2020 4:32 am

Messerbr wrote:http://www.reify-3d.com/forum/viewtopic.php?f=8&t=1180

Ramping straight to 1450 and holding for 3 or 4 hours then drop to casting temperature seems to work well.



I just do it today and the top of my flask was broken, with soluswax pro
so i have some doubts:

1. The ramping straight from 80F to 1450F in 1.5hrs was too fast??
for a flask of 2.5 in x 2.5 in, (just one ladies ring) that was sitting for 1.5 hrs after investing with ultravest maxx 38:100
What is a good time for reach the 1450F?

2. Or my kiln it's not enough calibrate and maybe is more than 1450F?

Regards

Who is online

Users browsing this forum: No registered users and 12 guests