EasyCast HD Print problems
- ReubenGabriel
- Novice
- Posts:31
- Joined:Fri Jun 17, 2016 5:39 pm
Thanks Monger. I'm still struggling and trying to figure it out. I've upped my exposure to 4.2 while printing at 20z now waiting on it. Hopefully it helps and I'll clean afterward.
- ReubenGabriel
- Novice
- Posts:31
- Joined:Fri Jun 17, 2016 5:39 pm
Re: EasyCast HD Print problems
No luck. I really don't understand what's going on. In between all this I had a "successful" print that had 4 designs correctly print and 1 failure. Now I'm just returning to all failures.
My Second attempt
My Second attempt
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: EasyCast HD Print problems
It's your supports. You're not doing them correctly. Need better orientation for the models and better supports. Thicker tips. Etc.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- ReubenGabriel
- Novice
- Posts:31
- Joined:Fri Jun 17, 2016 5:39 pm
Re: EasyCast HD Print problems
How thick are your tips generally?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: EasyCast HD Print problems
Anywhere from 0.3 - 0.6mm
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- ReubenGabriel
- Novice
- Posts:31
- Joined:Fri Jun 17, 2016 5:39 pm
Re: EasyCast HD Print problems
A new print test. Does this tell anything more? Or is it still supports?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: EasyCast HD Print problems
How many hours do you have on your projector bulb? Ever change it since 2016?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: EasyCast HD Print problems
Recalibrate the buildplate so it is level. If it is off a little it will fail to print. Or if it is pushing to hard on the Vat you can get problems in later layers where it wont stick anymore.
- ReubenGabriel
- Novice
- Posts:31
- Joined:Fri Jun 17, 2016 5:39 pm
Re: EasyCast HD Print problems
I bought this one used with light use but I just checked & have 1694 hours on the bulb it looks like so time for a new one. Thanks. I'll recalibrate the build plate too. thanks. Any top of the line site for the lamps (optoma hd37)?
- ReubenGabriel
- Novice
- Posts:31
- Joined:Fri Jun 17, 2016 5:39 pm
Re: EasyCast HD Print problems
Thanks everyone for your help. It looks like my biggest problems on both my machines was recalibrating the build plate. Thanks again Kokos & Monger.
Who is online
Users browsing this forum: No registered users and 0 guests