I just received the SolusCast and went over the instructions:
- Should I preheat the oven to 300F before inserting the flasks?
- What are the recommended temperature ramps (F/h) between the burnout phases?
- What is the recommended orientation of the flasks during burnout? With the sprue-gate Up or Down?
SolusCast Burnout
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: SolusCast Burnout
- Should I preheat the oven to 300F before inserting the flasks? Yes.
- What are the recommended temperature ramps (F/h) between the burnout phases?
According to our caster, if your oven has an automatic timer then it should calculate the ramp time already. That time was already included in the burnout times. Should ramp up to temp within 10-15 min, so should be around 28-30F per minute.
- What is the recommended orientation of the flasks during burnout? With the sprue-gate Up or Down? Down.
- What are the recommended temperature ramps (F/h) between the burnout phases?
According to our caster, if your oven has an automatic timer then it should calculate the ramp time already. That time was already included in the burnout times. Should ramp up to temp within 10-15 min, so should be around 28-30F per minute.
- What is the recommended orientation of the flasks during burnout? With the sprue-gate Up or Down? Down.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: SolusCast Burnout
Hi Emil , can you respond to my email I sent you having some problems and need some help?
also I was wondering what is the bench sit time after you finish your investment processes ??
also I was wondering what is the bench sit time after you finish your investment processes ??
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: SolusCast Burnout
rsaldivar wrote:Hi Emil , can you respond to my email I sent you having some problems and need some help?
also I was wondering what is the bench sit time after you finish your investment processes ??
I didn't get an email from you. Please send it again.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: SolusCast Burnout
what is the bench sit time after you finish your investment processes ??
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: SolusCast Burnout
The recommended bench time for the investment you're using.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: SolusCast Burnout
mongerdesigns wrote:According to our caster, if your oven has an automatic timer then it should calculate the ramp time already.
I have a Paragon programable oven. The controller allows the ramps to be programed from 1F to 1850F per hour. There is no Automatic setting. All resins I have experimented with so far require different burnout ramps. The copy of the instructions I received has only the hold times. Not the ramps (F per hour/minute).
mongerdesigns wrote:Should ramp up to temp within 10-15 min, so should be around 28-30F per minute.
Is that the ramp (30F/min) we should use between all 4 burnout phases? Usually different ramps are requred. Could you please confirm this with your caster or the resin developers.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: SolusCast Burnout
They said 28F per minute ramp time between temps.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: SolusCast Burnout
I use a 5 hour bench time af,ter, mixing. It may be overkill,but it works
Who is online
Users browsing this forum: No registered users and 3 guests