projector bulb not working
HI I HAVE Vivitek 1188 HD Projector when i switch on the projector power green light blink and fans working but Lamp not work.. can anyone help me with that?
Last edited by CHAMAL on Sat Feb 17, 2018 4:32 pm, edited 1 time in total.
W.A Chamal .S .Jayaratna
Jewelery CAD Designer
Jewellery Master model solution consultant
WEB - http://www.eoncadcam.com
Jewelery CAD Designer
Jewellery Master model solution consultant
WEB - http://www.eoncadcam.com
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: projector bulb not working
You have to count how many blinks it does before a short pause, then check the table in the attached pic for the issue. Good luck!
Re: projector bulb not working
green light was flashing thats all no red light and fans are normally working
except just on start i never seen the red light blink
except just on start i never seen the red light blink
W.A Chamal .S .Jayaratna
Jewelery CAD Designer
Jewellery Master model solution consultant
WEB - http://www.eoncadcam.com
Jewelery CAD Designer
Jewellery Master model solution consultant
WEB - http://www.eoncadcam.com
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: projector bulb not working
How many time the green light flashing before a short pause?
Re: projector bulb not working
Hello Everyone,
I'm facing same problem like CHAMAL, same Vivitek 1188hd projector keep on blinking, fan did not start after few second fan started, trying to shutdown it wont stop blinking and fan get slow sound and again rise the speed..
Already order bare bulb from Mark, lamp hours was more then 1200.
advice what could be?
Thank You.
I'm facing same problem like CHAMAL, same Vivitek 1188hd projector keep on blinking, fan did not start after few second fan started, trying to shutdown it wont stop blinking and fan get slow sound and again rise the speed..
Already order bare bulb from Mark, lamp hours was more then 1200.
advice what could be?
Thank You.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: projector bulb not working
How many times does it blink? Need to figure out which error message it is. Could be a thermal sensor.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: projector bulb not working
Erorr # System Intail, System power ON and Lamp fail,
showing 5blinking n fan speed increase n get low it's self. First when I press power button ON it takes time to warm up, before was quick.
video:- https://photos.app.goo.gl/TXW1Zsor7boZfK6W9
is it replaceable thermal sensor?
Thank You.
showing 5blinking n fan speed increase n get low it's self. First when I press power button ON it takes time to warm up, before was quick.
video:- https://photos.app.goo.gl/TXW1Zsor7boZfK6W9
is it replaceable thermal sensor?
Thank You.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: projector bulb not working
Yes, it's a replaceable part. If that's the problem for sure.
However you may need to send the projector to Vivitek or maybe a local tv repair shop can help, if the projector is out of warranty. Before you send the projector to Vivitek, don't forget to put the UV filter back in.
However you may need to send the projector to Vivitek or maybe a local tv repair shop can help, if the projector is out of warranty. Before you send the projector to Vivitek, don't forget to put the UV filter back in.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: projector bulb not working
bought in 2016 July with printer and we dont have service center in TANZANIA for Vivitek. in Kenya there is dealer but they don't do service.
Here TV repair shops can't trust .
as per your knowledge it is sure thermal sensor has gone? how it look any links.
Here TV repair shops can't trust .
as per your knowledge it is sure thermal sensor has gone? how it look any links.
Re: projector bulb not working
Hi,
Replaced blub (from Mark) working fine, had readjusted grid and reset resin profile.
Blub easy to replace.
Old blub image attached.
Replaced blub (from Mark) working fine, had readjusted grid and reset resin profile.
Blub easy to replace.
Old blub image attached.
Who is online
Users browsing this forum: No registered users and 0 guests