my recent castings

Discuss casting techniques
Post Reply
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm
my recent castings

Postby rsaldivar » Mon May 21, 2018 10:54 pm

not perfect but good enough for me
Attachments
20180521_162411.jpg
20180521_162408.jpg
20180521_162352.jpg
20180521_162323.jpg
20180521_162318.jpg
Top
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm

Re: my recent castings

Postby rsaldivar » Mon May 21, 2018 10:54 pm

more
Attachments
20180521_162830.jpg
20180521_162743.jpg
20180521_162519.jpg
20180521_162458.jpg
20180521_162449.jpg
Top
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm

Re: my recent castings

Postby rsaldivar » Mon May 21, 2018 11:08 pm

I would include the STL's , but I don't know how to load it ? sorry
Top
User avatar
mongerdesigns
Solus Guru
Posts:1951
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:
Contact mongerdesigns

Re: my recent castings

Postby mongerdesigns » Mon May 21, 2018 11:09 pm

Those are really good! Lettering is always a challenge. Looks like you got it down.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
Top
User avatar
rkundla
Solus Master
Posts:309
Joined:Sat Jan 09, 2016 6:01 am

Re: my recent castings

Postby rkundla » Tue May 22, 2018 4:34 pm

Nice clean lettering. Did you apply investment to the lettering first before investing the full flask?
Top
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm

Re: my recent castings

Postby rsaldivar » Fri May 25, 2018 4:50 pm

finished
Attachments
20180521_123541.jpg
20180516_113855.jpg
20180524_180433.jpg
20180524_180401.jpg
Top
User avatar
mongerdesigns
Solus Guru
Posts:1951
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:
Contact mongerdesigns

Re: my recent castings

Postby mongerdesigns » Fri May 25, 2018 5:05 pm

Did you over-polish the lettering? It's all rounded and less detailed now compared to the rough casting.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
Top
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm

Re: my recent castings

Postby rsaldivar » Fri May 25, 2018 6:34 pm

yes , a little , I kept until the pits went away
Top
User avatar
exedebee
Solus Expert
Posts:128
Joined:Fri Feb 12, 2016 3:39 am

Re: my recent castings

Postby exedebee » Sat May 26, 2018 12:58 am

clean casting.
Top
User avatar
M-Williams
Solus Master
Posts:393
Joined:Sun Nov 01, 2015 4:45 pm

Re: my recent castings

Postby M-Williams » Sat May 26, 2018 1:00 pm

rsaldivar wrote:finished


From The the Picture of the ring, I suspect your melting temperature was a bit high, and those small air trapped bubbles are the pits you were fighting to remove on the surface. you can laupe them clear on a polished area .
Top
Post Reply

Return to “Casting”

Who is online

Users browsing this forum: No registered users and 2 guests